dsPIC33FJ32MC104-I/PT Microchip Technology, dsPIC33FJ32MC104-I/PT Datasheet - Page 243

• Manufacturer Part Number: dsPIC33FJ32MC104-I/PT
• Description: Digital Signal Processors & Controllers - DSP, DSC 16bit Mtr Cnt Fam 16 MIPS 32KBFLSH 2KBRAM
• Manufacturer: Microchip Technology
• Type: dsPIC33FJ32(GP/MC)101/102/104r

Specifications of dsPIC33FJ32MC104-I/PT

• Rohs: yes
• Core: dsPIC33F
• Data Bus Width: 16 bit
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 7.37 MHz, 32 kHz
• Number Of Programmable I/os: 35
• Number Of Timers: 5 x 16-bit, 2 x 32-bit
• Device Million Instructions Per Second: 16 MIPs
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 125 C
• Package / Case: TQFP-44
• Mounting Style: SMD/SMT
• Family / Core: dsPIC33FJ32(GP/MC)101/102/104
• Interface Type: I2C, SPI, UART
• Minimum Operating Temperature: - 40 C
• On-chip Adc: Yes
• Product: DSPs
• Program Memory Type: Flash
• Supply Current: 10 mA

21.2
REGISTER 21-1:
 2011-2012 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9-8
Note 1:
RTCEN
dsPIC33FJ16(GP/MC)101/102 AND dsPIC33FJ32(GP/MC)101/102/104
R/W-0
R/W-0
2:
3:
RTCC Control Registers
(2)
The RCFGCAL register is only affected by a POR.
A write to the RTCEN bit is only allowed when RTCWREN = 1.
This bit is read-only; it is cleared to ‘0’ on a write to the lower half of the MINSEC register.
RTCEN: RTCC Enable bit
1 = RTCC module is enabled
0 = RTCC module is disabled
Unimplemented: Read as ‘0’
RTCWREN: RTCC Value Registers Write Enable bit
1 = RTCVALH and RTCVALL registers can be written to by the user
0 = RTCVALH and RTCVALL registers are locked out from being written to by the user
RTCSYNC: RTCC Value Registers Read Synchronization bit
1 = RTCVALH, RTCVALL and ALCFGRPT registers can change while reading, due to a rollover ripple,
0 = RTCVALH, RTCVALL or ALCFGRPT registers can be read without concern over a rollover ripple
HALFSEC: Half-Second Status bit
1 = Second half period of a second
0 = First half period of a second
RTCOE: RTCC Output Enable bit
1 = RTCC output is enabled
0 = RTCC output is disabled
RTCPTR<1:0>: RTCC Value Register Window Pointer bits
Points to the corresponding RTCC Value registers when reading RTCVALH and RTCVALL registers;
the RTCPTR<1:0> value decrements on every read or write of RTCVALH until it reaches ‘00’.
RTCVAL<15:8>:
00 = MINUTES
01 = WEEKDAY
10 = MONTH
11 = Reserved
RTCVAL<7:0>:
00 = SECONDS
01 = HOURS
10 = DAY
11 = YEAR
R/W-0
resulting in an invalid data read. If the register is read twice and the results are the same data, the
data can be assumed to be valid.
U-0
—
RCFGCAL: RTCC CALIBRATION AND CONFIGURATION REGISTER
W = Writable bit
‘1’ = Bit is set
RTCWREN
R/W-0
R/W-0
(2)
RTCSYNC HALFSEC
R/W-0
R-0
(3)
CAL<7:0>
‘0’ = Bit is cleared
U = Unimplemented bit, read as ‘0’
R/W-0
R-0
(3)
RTCOE
R/W-0
R/W-0
x = Bit is unknown
R/W-0
R/W-0
RTCPTR<1:0>
(1)
DS70652E-page 243
R/W-0
R/W-0
bit 8
bit 0