S9S12G96F0MLF Freescale Semiconductor, S9S12G96F0MLF Datasheet - Page 721

• Manufacturer Part Number: S9S12G96F0MLF
• Description: 16-bit Microcontrollers - MCU 16BIT 96K FLASH
• Manufacturer: Freescale Semiconductor

Specifications of S9S12G96F0MLF

• Rohs: yes
• Core: S12
• Processor Series: MC9S12G
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 25 MHz
• Program Memory Size: 96 KB
• Data Ram Size: 8192 B
• On-chip Adc: Yes
• Operating Supply Voltage: 3.13 V to 5.5 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: LQFP-48
• Mounting Style: SMD/SMT

In slave mode, if the SS line is not deasserted between the successive transmissions then the content of the
SPI data register is not transmitted; instead the last received data is transmitted. If the SS line is deasserted
for at least minimum idle time (half SCK cycle) between successive transmissions, then the content of the
SPI data register is transmitted.
In master mode, with slave select output enabled the SS line is always deasserted and reasserted between
successive transfers for at least minimum idle time.
21.4.3.3
Some peripherals require the first SCK edge before the first data bit becomes available at the data out pin,
the second edge clocks data into the system. In this format, the first SCK edge is issued by setting the
CPHA bit at the beginning of the n
The first edge of SCK occurs immediately after the half SCK clock cycle synchronization delay. This first
edge commands the slave to transfer its first data bit to the serial data input pin of the master.
1. n depends on the selected transfer width, please refer to
Freescale Semiconductor
End of Idle State
SCK Edge Number
SCK (CPOL = 0)
SCK (CPOL = 1)
SAMPLE I
MOSI/MISO
CHANGE O
CHANGE O
SEL SS (O)
Master only
SEL SS (I)
t
t
t
t
Figure 21-13. SPI Clock Format 0 (CPHA = 0), with 16-Bit Transfer Width selected (XFRW = 1)
MOSI pin
MISO pin
L
T
I
L
MSB first (LSBFE = 0)
LSB first (LSBFE = 1)
, t
= Minimum idling time between transfers (minimum SS high time)
= Minimum leading time before the first SCK edge
= Minimum trailing time after the last SCK edge
T
, and t
CPHA = 1 Transfer Format
I
are guaranteed for the master mode and required for the slave mode.
MSB
LSB
t
L
1
2
Bit 14
Bit 1
3
4
Bit 13
Bit 2
MC9S12G Family Reference Manual, Rev.1.23
5
Begin
6
1
Bit 12
Bit 3
-cycle transfer operation.
7
8
Bit 11
Bit 4
9
10
Bit 10 Bit 9 Bit 8 Bit 7 Bit 6
Bit 5
11
12
Bit 6
13
14
Section 21.3.2.2, “SPI Control Register 2 (SPICR2)
Transfer
Bit 7 Bit 8 Bit 9 Bit 10Bit 11Bit 12Bit 13Bit 14
15
16
17
18
19
20
Bit 5
21
22
Bit 4 Bit 3 Bit 2 Bit 1
23
24
25
End
26
27
Serial Peripheral Interface (S12SPIV5)
28
29
30
MSB
LSB
31
32
t
T
Minimum 1/2 SCK
for t
Begin of Idle State
t
I
t
T
L
, t
l
, t
L
723