HS7047KCM01H Renesas Electronics America, HS7047KCM01H Datasheet - Page 172

• Manufacturer Part Number: HS7047KCM01H
• Description: ON CHIP DEBUG EMULATOR
• Manufacturer: Renesas Electronics America
• Series: SuperH®r
• Type: In Circuit Debuggerr

Specifications of HS7047KCM01H

• Contents: Compact Emulator, IDE, Assembler and Linker
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With/related Products: SH7047
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant

Figure 6.2 shows the pin arrangement of the Hitachi-UDI port connector (36 pins).
4.09
Notes: 1. Handling of the TCK, TMS, TDI, TDO, /TRST, and /ASEBRKAK pins depends
148
2.8
+0.2
0
Figure 6.2 Pin Arrangement of the Hitachi-UDI Port Connector (36 Pins)
on the use conditions of the Hitachi-UDI as follows:
(a) When the user system is used by connecting the emulator, the TCK, TMS,
(b) When the user system is used independently without using the emulator and
Unit: mm
Hitachi-UDI port connector
Hitachi-UDI port connector
: Pattern inhibited area
TDI, TDO, /TRST, and /ASEBRKAK pins must be pulled up by a resistance
of several kilo-ohms. The /DBGMD pin must be grounded.
The AUDATA3 to AUDATA0, /AUDSYNC, and AUDMD pins must be pulled
up by a resistance of several kilo-ohms. The resistor of the AUDCK pin must
be terminated (pulled up and pulled down by a resistance of several kilo-
ohms).
The AUDRST pin must be pulled up by a resistance of several kilo-ohms (5
kilo-ohms or less).
Hitachi-UDI, the TCK, TMS, TDI, TDO, /TRST, and /ASEBRKAK pins must
be pulled up by a resistance of several kilo-ohms. The /DBGMD pin must be
also pulled up by a resistance of several kilo-ohms. The AUDCK, AUDATA3
to AUDATA0, /AUDSYNC, and AUDMD pins must be pulled up by a
resistance of several kilo-ohms.
The AUDRST pin must be pulled down by a resistance of several kilo-ohms.
(Pin 1 mark)
(Top view)
Edge of the board
(connected to the connector)
0.7
+0.1
0
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Notes:
Signal
AUDCK
GND
AUDATA0
GND
AUDATA1
GND
AUDATA2
GND
AUDATA3
GND
/AUDSYNC*
GND
AUDRST
GND
AUDMD
GND
TCK
GND
1. Input to or output from the user system.
2. The slash (/) means that the signal is low-active.
3.
The emulator monitors the GND signal of the user
system through the UCONNECT and detects whether
or not the user system is connected.
2
I/O
I/O
I/O
I/O
I/O
Input
Input
Input/
Output
I/O
Input
*1
SH7047F
Pin No.
79
92
90
88
86
78
81
63
80
Note
Pin
No.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
/ASEBRKAK
Signal
TMS
GND
/TRST*
GND
TDI
GND
TDO
GND
GND
CK
GND
/RES*
GND
GND*
GND
NC
GND
3
2
2
Output
Input/
Output
Output
Output
Input
Input
Input
Output
Output
*1
SH7047F
Pin No.
59
58
61
60
11
51
87
User reset
Note