ST92F150CV1TB STMicroelectronics, ST92F150CV1TB Datasheet - Page 120

• Manufacturer Part Number: ST92F150CV1TB
• Description: MCU 8BIT 128K FLASH 100TQFP
• Manufacturer: STMicroelectronics
• Series: ST9r

Specifications of ST92F150CV1TB

• Core Processor: ST9
• Core Size: 8/16-Bit
• Speed: 24MHz
• Connectivity: CAN, EBI/EMI, I²C, LIN, SCI, SPI
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 77
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: ST92F15x
• Core: ST9
• Data Bus Width: 8 bit, 16 bit
• Data Ram Size: 6 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 80
• Number Of Timers: 5 x 16 bit
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST92F150-EPB
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit x 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-4883

ST92F124/F150/F250 - INTERRUPTS
WAKE-UP / INTERRUPT LINES MANAGEMENT UNIT (Cont’d)
WAKE-UP
(WUTRH)
R252 - Read/Write
Register Page: 57
Reset Value: 0000 0000 (00h)
Bit 7:0 = WUT[15:8]: Wake-Up Trigger Polarity
Bits
These bits are set and cleared by software.
0: The corresponding WUPx pending bit will be set
1: The corresponding WUPx pending bit will be set
WAKE-UP TRIGGER REGISTER LOW (WUTRL)
R253 - Read/Write
Register Page: 57
Reset Value: 0000 0000 (00h)
Bit 7:0 = WUT[7:0]: Wake-Up Trigger Polarity Bits
These bits are set and cleared by software.
0: The corresponding WUPx pending bit will be set
1: The corresponding WUPx pending bit will be set
WARNING
1. As the external wake-up lines are edge trig-
2. If either a rising or a falling edge on the external
120/429
WUT15 WUT14 WUT13 WUT12 WUT11 WUT10 WUT9
9
WUT7
on the falling edge of the input wake-up line .
on the rising edge of the input wake-up line.
on the falling edge of the input wake-up line.
on the rising edge of the input wake-up line.
gered, no glitches must be generated on these
lines.
wake-up
WUTRLH or WUTRL registers, the pending bit
will not be set.
7
7
WUT6
WUT5
lines
TRIGGER
WUT4
occurs
WUT3
REGISTER
while
WUT2
writing
WUT1
HIGH
WUT8
WUT0
0
0
the
WAKE-UP PENDING REGISTER HIGH
(WUPRH)
R254 - Read/Write
Register Page: 57
Reset Value: 0000 0000 (00h)
Bit 7:0 = WUP[15:8]: Wake-Up Pending Bits
These bits are set by hardware on occurrence of
the trigger event on the corresponding wake-up
line. They must be cleared by software. They can
be set by software to implement a software inter-
rupt.
0: No Wake-up Trigger event occurred
1: Wake-up Trigger event occured
WAKE-UP PENDING REGISTER LOW (WUPRL)
R255 - Read/Write
Register Page: 57
Reset Value: 0000 0000 (00h)
Bit 7:0 = WUP[7:0]: Wake-Up Pending Bits
These bits are set by hardware on occurrence of
the trigger event on the corresponding wake-up
line. They must be cleared by software. They can
be set by software to implement a software inter-
rupt.
0: No Wake-up Trigger event occurred
1: Wake-up Trigger event occured
Note: To avoid losing a trigger event while clear-
ing the pending bits, it is recommended to use
read-modify-write
BAND) to clear them.
5.12.6 Important Note On WUIMU
Refer to
WUP15 WUP14 WUP13 WUP12 WUP11 WUP10 WUP9
WUP7
7
7
WUP6
Section 13.2 on page
WUP5
instructions
WUP4
WUP3
409.
WUP2
(AND,
WUP1
BRES,
WUP8
WUP0
0
0