S9S08DZ96F2MLF Freescale Semiconductor, S9S08DZ96F2MLF Datasheet - Page 406

• Manufacturer Part Number: S9S08DZ96F2MLF
• Description: MCU 96K FLASH MASK AUTO 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of S9S08DZ96F2MLF

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 39
• Program Memory Size: 96KB (96K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Processor Series: S08D
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 6 KB
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 87
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08DZ60
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 18 Debug Module (S08DBGV3) (128K)
18.3.3.13 Debug Control Register (DBGC)
1
406
end-run
Module Base + 0x000C
end-run
or non-
In the case of an end-trace to reset where DBGEN=1 and BEGIN=0, the ARM and BRKEN bits are cleared but the remaining
control bits in this register do not change after reset.
DBGEN
BRKEN
LOOP1
Reset
Field
ARM
POR
TAG
7
6
5
4
0
W
R
1
DBGEN
DBG Module Enable Bit — The DBGEN bit enables the DBG module. The DBGEN bit is forced to zero and
cannot be set if the MCU is secure.
0 DBG not enabled
1 DBG enabled
Arm Bit — The ARM bit controls whether the debugger is comparing and storing data in FIFO. See
Section 18.4.4.2, “Arming the DBG Module”
0 Debugger not armed
1 Debugger armed
Tag or Force Bit — The TAG bit controls whether a debugger or comparator C breakpoint will be requested as
a tag or force breakpoint to the CPU. The TAG bit is not used if BRKEN = 0.
0 Force request selected
1 Tag request selected
Break Enable Bit — The BRKEN bit controls whether the debugger will request a breakpoint to the CPU at the
end of a trace run, and whether comparator C will request a breakpoint to the CPU.
0 CPU break request not enabled
1 CPU break request enabled
Select LOOP1 Capture Mode — This bit selects either normal capture mode or LOOP1 capture mode. LOOP1
is not used in event-only modes.
0 Normal operation - capture COF events into the capture buffer FIFO
1 LOOP1 capture mode enabled. When the conditions are met to store a COF value into the FIFO, compare the
U
1
7
current COF address with the address in comparator C. If these addresses match, override the FIFO capture
and do not increment the FIFO count. If the address does not match comparator C, capture the COF address,
including the PPACC indicator, into the FIFO and into comparator C.
= Unimplemented or Reserved
ARM
1
0
6
Figure 18-14. Debug Control Register (DBGC)
Table 18-15. DBGC Field Descriptions
MC9S08DZ128 Series Data Sheet, Rev. 1
TAG
U
0
5
BRKEN
for more information.
0
0
4
Description
0
0
0
3
0
0
0
2
Freescale Semiconductor
0
0
0
1
LOOP1
U
0
0