MC68HC908EY16CFA Freescale Semiconductor, MC68HC908EY16CFA Datasheet - Page 164

• Manufacturer Part Number: MC68HC908EY16CFA
• Description: IC MCU 16K FLASH 8MHZ SPI 32LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908EY16CFA

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LIN, SCI, SPI
• Peripherals: POR, PWM
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: HC08EY
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05CE, ZK-HC08EY-A
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No

System Integration Module (SIM)
14.5.3 Break Interrupts
The break module can stop normal program flow at a software-programmable break point by asserting its
break interrupt output. See
forcing it to the SWI vector location. Refer to the break interrupt subsection of each module to see how
each module is affected by the break state.
14.5.4 Status Flag Protection in Break Mode
The SIM controls whether status flags contained in other modules can be cleared during break mode. The
user can select whether flags are protected from being cleared by properly initializing the break clear flag
enable bit (BCFE) in the SIM break flag control register (SBFCR).
Protecting flags in break mode ensures that set flags will not be cleared while in break mode. This
protection allows registers to be freely read and written during break mode without losing status flag
information.
Setting the BCFE bit enables the clearing mechanisms. Once cleared in break mode, a flag remains
cleared even when break mode is exited. Status flags with a two-step clearing mechanism — for example,
a read of one register followed by the read or write of another — are protected, even when the first step
is accomplished prior to entering break mode. Upon leaving break mode, execution of the second step
will clear the flag as normal.
14.6 Low-Power Modes
Executing the WAIT or STOP instruction puts the MCU in a low power- consumption mode for standby
situations. The SIM holds the CPU in a non-clocked state. Both STOP and WAIT clear the interrupt mask
(I) in the condition code register, allowing interrupts to occur. Low-power modes are exited via an interrupt
or reset.
14.6.1 Wait Mode
In wait mode, the CPU clocks are inactive while one set of peripheral clocks continues to run.
Figure 14-11
A module that is active during wait mode can wake up the CPU with an interrupt if the interrupt is enabled.
Stacking for the interrupt begins one cycle after the WAIT instruction during which the interrupt occurred.
Refer to the wait mode subsection of each module to see if the module is active or inactive in wait mode.
Some modules can be programmed to be active in wait mode.
Wait mode can also be exited by a reset. If the COP disable bit, COPD, in the configuration register is 0,
then the computer operating properly module (COP) is enabled and remains active in wait mode.
164
shows the timing for wait mode entry.
R/W
IDB
IAB
Note: Previous data can be operand data or the WAIT opcode, depending on the last instruction.
WAIT ADDR
19.2 Break Module
MC68HC908EY16 • MC68HC908EY8 Data Sheet, Rev. 10
PREVIOUS DATA
Figure 14-11. Wait Mode Entry Timing
WAIT ADDR + 1
NEXT OPCODE
(BRK). The SIM puts the CPU into the break state by
SAME
SAME
SAME
SAME
Freescale Semiconductor