AM79C875KI AMD (ADVANCED MICRO DEVICES), AM79C875KI Datasheet - Page 11

• Manufacturer Part Number: AM79C875KI
• Manufacturer: AMD (ADVANCED MICRO DEVICES)

Specifications of AM79C875KI

• Lead Free Status / RoHS Status: Not Compliant

MDIO
Management Data I/O
This pin is a bidirectional data interface used by the
MAC to access management register within the Net-
PHY™ 4LP device. This pin has an internal pull-down,
therefore, it requires an external pull-up resistor (1.5
KΩ) as specified in IEEE-802.3 section 22.
MDC
Management Data Clock
This pin is the serial management clock which is used
to clock MDIO data to the MAC.
RST
Reset
An active low input will force the NetPHY™ 4LP device
to a known reset state. Reset also can be done through
the internal power-on-reset or MII Register 0, bit 15.
INTR
Interrupt
This pin is true whenever the NetPHY™ 4LP device
detects an event flagged as an interrupt. Events to be
flagged are programmed in Register 17. Interrupts are
cleared on Read. The polarity of INTR (active HIGH or
active LOW) is set by Register 16, bit 14. The default is
active LOW, which requires a 10 KΩ pull-up resistor.
LED Port
Note: Consult the LED Port Configuration section for
appropriate pull-up and pull-down resistors.
LEDDPX[0]/FX_DIS
Port [0] Duplex LED
Low LED indicates full-duplex and high indicates half-
duplex.
FX Mode: Pulled low at reset will put Port 3 in
100BASE-FX mode.
LEDACT_LINK[0]
Port [0] Transmit/Receive Activity LED
LED is output low for approximately 30 ms each time
there is activity. LINK is an active low signal. This signal
should have a 1k–4.7KΩ pull-up resistor.
LEDSPD[0]/TP1_1
Port [0] Speed LED
LED is output low when operating in 100BASE-X
modes and high when operating in 10BASE-T modes.
TP1_1: Pulled low at reset will select transmit trans-
former ratio to be 1.25:1. Default is 1:1 transformer.
LEDDPX[1]/PHYAD[4]
Port [1] Duplex LED
LED low indicates full-duplex and high indicates half-
duplex.
Input/Output, Pull-Down
Input/Output, Pull-Up
Input/Output, Pull-Up
Input/Output, Pull-Up
Input, Pull-Down
Output, Pull-Up
Input, Pull-Up
Tri-State
Am79C875
PHY Address[4]. This is the first address bit received
in the management frame, and one of three MSBs for
MII management PHY address. The two LSBs, PHYAD
[1:0] are internally wired to four ports: PHYAD
[11]=Port3,..., PHYAD [00] = Port0. The PHYAD will
also determine the scramble seed, this will help to
reduce EMI when there are multiple ports switching at
the same time. To set this pin, use pull-up or pull-down
resistors in the range of 1 KΩ to 4.7 KΩ.
LEDACT_LINK[1]/PHYAD[3]
Port [1] Transmit/Receive Activity LED
LED is output low for approximately 30 ms each time
there is activity. LINK is an active low signal.
PHY Address[3]. This is the second MSB and one of
three MSB’s for MII management PHY address. To set
this pin, use pull-up or pull-down resistors in the range
of 1 KΩ to 4.7 KΩ.
LEDSPD[1]/PHYAD[2]
Port [1] Speed LED
LED is output low when operating in 100BASE-X
modes and high when operating in 10BASE-T modes.
PHY Address[2]. This is the third MSB and one of
three MSB’s for MII management PHY address. To set
this pin, use pull-up or pull-down resistors in the range
of 1 KΩ to 4.7 KΩ.
LEDDPX[2]/DPLX
Port [2] Duplex LED
LED low indicates full-duplex and high indicates half-
duplex.
DPLX: Full Duplex Mode Enable. This pin is logically
OR’ed with a full-duplex enable MII control bit to gener-
ate an internal full-duplex enable signal. When as-
serted high, the NetPHY™ 4LP device operates in full-
duplex mode as determined through Auto-Negotiation
or software setting. When asserted low, the internal
control bit (Register 0, bit 8) will determine the full-du-
plex operating mode.
LEDACT_LINK[2]
Port [2] Transmit/Receive Activity LED
LED is output low for approximately 30 ms each time
there is activity. LINK is an active low signal. This signal
should have a 1k–4.7KΩ pull-up.
LEDSPD[2]/FORCE100
Port [2] Speed LED
LED is output low when operating in 100BASE-X
modes and high when operating in 10BASE-T modes.
FORCE100: Force 100BASE-X Operation. When this
signal is pulled high and ANEGA is low at reset, all
ports will be forced to 100BASE-TX operation. When
asserted low and ANEGA is low, all ports are forced to
Input/Output, Pull-Up
Input/Output, Pull-Up
Input/Output, Pull-Up
Input/Output, Pull-Up
Output, Pull-Up
11