PIC16F1937-E/MV Microchip Technology, PIC16F1937-E/MV Datasheet - Page 216

• Manufacturer Part Number: PIC16F1937-E/MV
• Description: 14KB Flash, 512B RAM, 256B EEPROM, LCD, 1.8-5.5V 40 UQFN 5x5x0.5mm TUBE
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1937-E/MV

• Processor Series: PIC16F
• Core: PIC
• Program Memory Type: Flash
• Program Memory Size: 14 KB
• Data Ram Size: 256 B
• Interface Type: MI2C, SPI, EUSART
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Package / Case: UQFN-40
• Development Tools By Supplier: MPLAB IDE Software
• Minimum Operating Temperature: - 40 C
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Lead Free Status / Rohs Status: Details

PIC16(L)F1934/6/7
23.3
Pulse-Width Modulation (PWM) is a scheme that
provides power to a load by switching quickly between
fully on and fully off states. The PWM signal resembles
a square wave where the high portion of the signal is
considered the on state and the low portion of the signal
is considered the off state. The high portion, also known
as the pulse width, can vary in time and is defined in
steps. A larger number of steps applied, which
lengthens the pulse width, also supplies more power to
the load. Lowering the number of steps applied, which
shortens the pulse width, supplies less power. The
PWM period is defined as the duration of one complete
cycle or the total amount of on and off time combined.
PWM resolution defines the maximum number of steps
that can be present in a single PWM period. A higher
resolution allows for more precise control of the pulse
width time and in turn the power that is applied to the
load.
The term duty cycle describes the proportion of the on
time to the off time and is expressed in percentages,
where 0% is fully off and 100% is fully on. A lower duty
cycle corresponds to less power applied and a higher
duty cycle corresponds to more power applied.
Figure 23-3
signal.
23.3.1
The standard PWM function described in this section is
available and identical for CCP modules ECCP1,
ECCP2, ECCP3, CCP4 and CCP5.
The standard PWM mode generates a Pulse-Width
modulation (PWM) signal on the CCPx pin with up to 10
bits of resolution. The period, duty cycle, and resolution
are controlled by the following registers:
• PRx registers
• TxCON registers
• CCPRxL registers
• CCPxCON registers
Figure 23-4
operation.
DS41364E-page 216
Note 1: The corresponding TRIS bit must be
2: Clearing the CCPxCON register will
PWM Overview
STANDARD PWM OPERATION
shows a simplified block diagram of PWM
cleared to enable the PWM output on the
CCPx pin.
relinquish control of the CCPx pin.
shows a typical waveform of the PWM
FIGURE 23-3:
FIGURE 23-4:
Note 1:
CCPRxH
Duty Cycle Registers
Comparator
2:
Pulse Width
CCPRxL
TMRx = 0
PRx
TMRx
Comparator
The 8-bit timer TMRx register is concatenated
with the 2-bit internal system clock (F
2 bits of the prescaler, to create the 10-bit time
base.
In PWM mode, CCPRxH is a read-only register.
(2)
Period
(Slave)
 2008-2011 Microchip Technology Inc.
CCP PWM OUTPUT SIGNAL
(1)
SIMPLIFIED PWM BLOCK
DIAGRAM
Clear Timer,
toggle CCPx pin and
latch duty cycle
TMRx = CCPRxH:CCPxCON<5:4>
CCPxCON<5:4>
TMRx = PRx
S
R
Q
TRIS
OSC
CCPx
), or