EP1AGX20CF484C6N Altera, EP1AGX20CF484C6N Datasheet - Page 93

• Manufacturer Part Number: EP1AGX20CF484C6N
• Description: IC ARRIA GX FPGA 20K 484FBGA
• Manufacturer: Altera
• Series: Arria GXr

Specifications of EP1AGX20CF484C6N

• Number Of Logic Elements/cells: 21580
• Number Of Labs/clbs: 1079
• Total Ram Bits: 1229184
• Number Of I /o: 230
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 484-FBGA
• Family Name: Arria™ GX
• Number Of Logic Blocks/elements: 21580
• # I/os (max): 230
• Process Technology: CMOS
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 21580
• Ram Bits: 1229184
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 484
• Package Type: FC-FBGA
• No. Of Macrocells: 21580
• Family Type: Arria GX
• No. Of I/o's: 230
• Operating Frequency Max: 622.08MHz
• Operating Temperature Range: 0°C To +85°C
• Logic Case Style: BGA
• No. Of Pins: 484
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-2395

Chapter 2: Arria GX Architecture
I/O Structure
Double Data Rate I/O Pins
© December 2009 Altera Corporation
A path in which a pin directly drives a register can require the delay to ensure zero
hold time, whereas a path in which a pin drives a register through combinational logic
may not require the delay. Programmable delays exist for decreasing
input-pin-to-logic-array and IOE input register delays. The Quartus II Compiler can
program these delays to automatically minimize setup time while providing a zero
hold time. Programmable delays can increase the register-to-pin delays for output
and/or output enable registers. Programmable delays are no longer required to
ensure zero hold times for logic array register-to-IOE register transfers. The Quartus II
Compiler can create zero hold time for these transfers.
programmable delays for Arria GX devices.
Table 2–22. Arria GX Devices Programmable Delay Chain
IOE registers in Arria GX devices share the same source for clear or preset. You can
program preset or clear for each individual IOE. You can also program the registers to
power up high or low after configuration is complete. If programmed to power up
low, an asynchronous clear can control the registers. If programmed to power up
high, an asynchronous preset can control the registers. This feature prevents the
inadvertent activation of another device’s active-low input upon power-up. If one
register in an IOE uses a preset or clear signal, all registers in the IOE must use that
same signal if they require preset or clear. Additionally, a synchronous reset signal is
available for the IOE registers.
Arria GX devices have six registers in the IOE, which support DDR interfacing by
clocking data on both positive and negative clock edges. The IOEs in Arria GX devices
support DDR inputs, DDR outputs, and bidirectional DDR modes. When using the
IOE for DDR inputs, the two input registers clock double rate input data on
alternating edges. An input latch is also used in the IOE for DDR input acquisition.
The latch holds the data that is present during the clock high times, allowing both bits
of data to be synchronous with the same clock edge (either rising or falling).
Figure 2–73
input timing diagram.
Input pin to logic array delay
Input pin to input register delay
Output pin delay
Output enable register t
Programmable Delays
shows an IOE configured for DDR input.
CO
delay
Input delay from pin to internal cells
Input delay from pin to input register
Delay from output register to output pin
Delay to output enable pin
Quartus II Logic Option
Figure 2–74
Table 2–22
Arria GX Device Handbook, Volume 1
shows the
shows the DDR
2–87