TDA1566TH/N1C,118 NXP Semiconductors, TDA1566TH/N1C,118 Datasheet - Page 7

• Manufacturer Part Number: TDA1566TH/N1C,118
• Description: IC AMP AUDIO PWR 150W AB 24HSOP
• Manufacturer: NXP Semiconductors
• Type: Class ABr

Specifications of TDA1566TH/N1C,118

• Output Type: 1-Channel (Mono) or 2-Channel (Stereo)
• Package / Case: 24-HSOP
• Max Output Power X Channels @ Load: 150W x 1 @ 1 Ohm; 75W x 2 @ 2 Ohm
• Voltage - Supply: 6.5 V ~ 18 V
• Features: Depop, I²C, Mute, Short-Circuit and Thermal Protection, Standby
• Mounting Type: Surface Mount
• Product: Class-AB
• Output Power: 92 W
• Available Set Gain: 26 dB
• Common Mode Rejection Ratio (min): 60 dB
• Thd Plus Noise: 0.2 %
• Operating Supply Voltage: 14.4 V
• Maximum Power Dissipation: 80000 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Audio Load Resistance: 4 Ohms
• Input Signal Type: Differential
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential
• Supply Type: Single
• Supply Voltage (max): 18 V
• Operational Class: Class-AB
• Audio Amplifier Output Configuration: 2-Channel Stereo
• Audio Amplifier Function: Speaker
• Single Supply Voltage (typ): 14.4V
• Dual Supply Voltage (typ): Not RequiredV
• Power Supply Requirement: Single
• Power Dissipation: 80W
• Rail/rail I/o Type: No
• Single Supply Voltage (max): 18V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 24
• Package Type: HSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 935284624118; TDA1566TH/N1C-T; TDA1566TH/N1C-T

NXP Semiconductors
6. Functional description
TDA1566_2
Product data sheet
6.1.1 Mode selection
6.1 General
Table 3.
Naming conventions used in this document:
The ADS1 pin selects the I
Section 6.1.6
Table 4.
Table 5
operates at CMOS compatible LOW and HIGH logic levels. With the EN pin LOW the
TDA1566 is switched off and the quiescent current is at its lowest value. With the enable
pin HIGH the operation mode of the TDA1566 is selected with IB1[D0] and IB1[D1]. The
I
Table 5.
In non-I
operation mode is selected with the EN pin.
at the EN pin in I
“Characteristics”.
Symbol
SCL
SDA
TAB
Pin
ADS1
EN pin
HIGH (> 2.6 V)
LOW (< 1.0 V)
2
•
•
C-bus instruction and data bytes are described in
Reference to bits in instruction bytes: IBx[Dy] refers to bit Dy of instruction byte x
Reference to bits in data bytes: DBx[Dy] refers to bit Dy of data byte x
2
lists the control for the I
C-bus mode the TDA1566 has 3 operation modes: off/mute/operation. The
Pin description TDA1566J
Mode selection with the ADS1 pin
I
2
C-bus mode operation
and
2
Pin
25
26
27
C-bus and non-I
Section 6.4.3
Rev. 02 — 20 August 2007
IB1[D0]
1
1
0
don’t care
2
C-bus or non-I
Description
I
I
connect to PGND
I
2
2
2
C-bus clock input
C-bus data input/output
Non-I
GND
C-bus controlled dual channel/single channel amplifier
2
for the ADS1 pin functionality.
C-bus mode operation. In I
2
C-bus mode. For the voltage levels see
2
C-bus mode
…continued
2
C-bus mode operation as listed in
Figure 5
IB2[D0]
0
1
don’t care
don’t care
Section 6.4.2
displays the required voltage levels
2
C-bus mode the EN pin
I
open or via 33 k to GND
2
C-bus mode
and
Operation mode
operating
mute
standby
off
Section
TDA1566
© NXP B.V. 2007. All rights reserved.
Section 9
Table
6.4.3.
4. See
7 of 46