TDA1566TH/N1C,118 NXP Semiconductors, TDA1566TH/N1C,118 Datasheet - Page 9

• Manufacturer Part Number: TDA1566TH/N1C,118
• Description: IC AMP AUDIO PWR 150W AB 24HSOP
• Manufacturer: NXP Semiconductors
• Type: Class ABr

Specifications of TDA1566TH/N1C,118

• Output Type: 1-Channel (Mono) or 2-Channel (Stereo)
• Package / Case: 24-HSOP
• Max Output Power X Channels @ Load: 150W x 1 @ 1 Ohm; 75W x 2 @ 2 Ohm
• Voltage - Supply: 6.5 V ~ 18 V
• Features: Depop, I²C, Mute, Short-Circuit and Thermal Protection, Standby
• Mounting Type: Surface Mount
• Product: Class-AB
• Output Power: 92 W
• Available Set Gain: 26 dB
• Common Mode Rejection Ratio (min): 60 dB
• Thd Plus Noise: 0.2 %
• Operating Supply Voltage: 14.4 V
• Maximum Power Dissipation: 80000 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Audio Load Resistance: 4 Ohms
• Input Signal Type: Differential
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential
• Supply Type: Single
• Supply Voltage (max): 18 V
• Operational Class: Class-AB
• Audio Amplifier Output Configuration: 2-Channel Stereo
• Audio Amplifier Function: Speaker
• Single Supply Voltage (typ): 14.4V
• Dual Supply Voltage (typ): Not RequiredV
• Power Supply Requirement: Single
• Power Dissipation: 80W
• Rail/rail I/o Type: No
• Single Supply Voltage (max): 18V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 24
• Package Type: HSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 935284624118; TDA1566TH/N1C-T; TDA1566TH/N1C-T

NXP Semiconductors
Table 9.
TDA1566_2
Product data sheet
Symbol
IN2+
IN2
IN1+
IN1
1OHM
OUT1+
OUT1
OUT2+
OUT2
Pinning for the single channel 1
Pin
(TDA1566TH)
2
3
10
11
15
16
18
19
21
6.1.3 Balanced and unbalanced input sources
6.1.4 Single channel 1
The TDA1566 accepts balanced as well as unbalanced input signals.
show the required hard or software setting and
connection. Note that the unbalanced input source should be connected to the positive
BTL channel input. Note that the J version accepts in non-I
input source.
Table 7.
Table 8.
The input and output pins for single channel 1
operation requires that on the PCB the output pins are shorted as indicated in
the 1
To prevent instability in 1
with a load larger than 25 .
Source
I
Non-I
Source
I
Non-I
2
2
Fig 6. Balanced (left) and unbalanced (right) input source
C-bus mode
C-bus mode
Pin
(TDA1566J)
22
23
3
4
8
10
13
15
18
2
2
C-bus mode
C-bus mode
operation the input signal is taken from channel 1.
Balanced and unbalanced input source setting TDA1566TH
Balanced and unbalanced input source setting TDA1566J
Description single channel
operation
disabled: connect IN2+ with 470 nF
to SGND
disabled: connect IN2+ with 470 nF
to SGND
positive input channel 1
negative input channel 1
1
positive output channel 1
negative output channel 1
shorted on board to OUT1
shorted on board to OUT1+
mode; TDA1566TH and TDA1566J
Rev. 02 — 20 August 2007
operation
select pin connected to V
operation the amplifier must not be used in line driver mode
I
2
Balanced input source
IB3[D1] = 0
ADS2 pin connected to GND
Balanced input source
IB3[D1] = 0
default
C-bus controlled dual channel/single channel amplifier
P
Figure 6
operation are listed in
Description dual channel
operation
positive input channel 2
negative input channel 2
positive input channel 1
negative input channel 1
1
positive output channel 1
negative output channel 1
positive output channel 2
negative output channel 2
shows the input source
select pin connected to GND
2
C-bus mode only a balanced
Unbalanced input source
IB3[D1] = 1
ADS2 pin unconnected
Unbalanced input source
IB3[D1] = 1
not selectable
001aad009
Table 7
TDA1566
© NXP B.V. 2007. All rights reserved.
Table
9. The 1
and
Table
Table 8
9 of 46
9. In