S71GL064A08 SPANSION [SPANSION], S71GL064A08 Datasheet - Page 31

• Manufacturer Part Number: S71GL064A08
• Description: STACKED MULTI CHIP PRODUCT FLASH MEMORY AND RAM
• Manufacturer: SPANSION [SPANSION]

February 8, 2005 S71GL064A_00_A2
Sector
SA120
SA122
SA123
SA124
SA125
SA126
SA127
SA128
SA129
SA130
SA132
SA134
SA114
SA115
SA116
SA117
SA118
SA119
SA121
SA133
SA131
Autoselect Mode
The autoselect mode provides manufacturer and device identification, and sector group pro-
tection verification, through identifier codes output on DQ7–DQ0. This mode is primarily
intended for programming equipment to automatically match a device to be programmed
with its corresponding programming algorithm. However, the autoselect codes can also be ac-
cessed in-system through the command register.
When using programming equipment, the autoselect mode requires VID on address pin A9.
Address pins A6, A3, A2, A1, and A0 must be as shown in
sector protection, the sector address must appear on the appropriate highest order address
bits.
have been set as required, the programming equipment may then read the corresponding
identifier code on DQ7–DQ0.
To access the autoselect codes in-system, the host system can issue the autoselect command
via the command register, as shown in
the Autoselect Command Sequence section for more information.
Sector Address
Table 3. S29GL064A Bottom Boot Sector Architecture (Continued)
Table 4
1110000xxx
1101100xxx
1110001xxx
1110010xxx
1110100xxx
1111000xxx
1101011xxx
1101101xxx
1101110xxx
1110011xxx
1110101xxx
1110110xxx
1111001xxx
1111010xxx
1111100xxx
A21–A12
1101111xxx
1110111xxx
1111011xxx
1111101xxx
1111110xxx
1111111000
A d v a n c e
shows the remaining address bits that are don’t care. When all necessary bits
(KBs/Kwords)
Sector Size
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
64/32
I n f o r m a t i o n
S71GL064A based MCPs
Table
6C0000h–6CFFFFh
6D0000h–6DFFFFh
7D0000h–7DFFFFh
7A0000h–7AFFFFh
7C0000h–7CFFFFh
6B0000h–6BFFFFh
6E0000h–6EFFFFh
700000h–70FFFFh
780000h–78FFFFh
7B0000h–7BFFFFh
6F0000h–6FFFFFh
720000h–72FFFFh
730000h–73FFFFh
740000h–74FFFFh
750000h–75FFFFh
760000h–76FFFFh
770000h–77FFFFh
790000h–79FFFFh
7E0000h–7EFFFFh
7F0000h–7FFFFFh
10. This method does not require V
Address Range
710000h–71FFFFh
(x8)
Table
4. In addition, when verifying
3D0000h–3D7FFFh
3D8000h–3DFFFFh
3A0000h–3A7FFFh
3A8000h–3AFFFFh
3C0000h–3C7FFFh
3C8000h–3CFFFFh
380000h–387FFFh
388000h–38FFFFh
3B0000h–3B7FFFh
3B8000h–3BFFFFh
358000h–35FFFFh
360000h–367FFFh
368000h–36FFFFh
370000h–377FFFh
378000h–37FFFFh
390000h–397FFFh
398000h–39FFFFh
3E0000h–3E7FFFh
3E8000h–3EFFFFh
3F0000h–3F7FFFh
3F8000h–3FFFFFh
Address Range
(x16)
ID
. Refer to
29