LPC1778FBD144,551 NXP Semiconductors, LPC1778FBD144,551 Datasheet - Page 53

• Manufacturer Part Number: LPC1778FBD144,551
• Description: ARM Microcontrollers - MCU CORTEX-M3 512KB FL 96KB SRAM USB 2.0
• Manufacturer: NXP Semiconductors

Specifications of LPC1778FBD144,551

• Rohs: yes
• Core: ARM Cortex M3
• Processor Series: LPC178x
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 120 MHz
• Program Memory Size: 512 KB
• Data Ram Size: 64 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2.4 V to 3.6 V
• Package / Case: LQFP-144
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 8
• Interface Type: CAN, I2C, I2S, SSP
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 165
• Number Of Timers: 4
• On-chip Dac: Yes
• Program Memory Type: Flash
• Factory Pack Quantity: 60
• Supply Voltage - Max: 3.6 V
• Supply Voltage - Min: 2.4 V

NXP Semiconductors
LPC178X_7X
Product data sheet
7.19.1 Features
7.20.1 Features
7.20 UARTs
7.21 SSP serial I/O controller
Remark: USART4 is not available on part LPC1774FBD144.
The LPC178x/7x contain five UARTs. In addition to standard transmit and receive data
lines, UART1 also provides a full modem control handshake interface and support for
RS-485/9-bit mode allowing both software address detection and automatic address
detection using 9-bit mode.
The UARTs include a fractional baud rate generator. Standard baud rates such as
115200 Bd can be achieved with any crystal frequency above 2 MHz.
The LPC178x/7x contain three SSP controllers. The SSP controller is capable of
operation on a SPI, 4-wire SSI, or Microwire bus. It can interact with multiple masters and
slaves on the bus. Only a single master and a single slave can communicate on the bus
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
10-bit DAC
Resistor string architecture
Buffered output
Power-down mode
Selectable output drive
Dedicated conversion timer
DMA support
Maximum UART data bit rate of 7.5 MBit/s.
16 B Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
Auto-baud capability.
Fractional divider for baud rate control, auto baud capabilities and FIFO control
mechanism that enables software flow control implementation.
Support for RS-485/9-bit/EIA-485 mode and multiprocessor addressing.
All UARTs have DMA support for both transmit and receive.
UART1 equipped with standard modem interface signals. This module also provides
full support for hardware flow control (auto-CTS/RTS).
USART4 includes an IrDA mode to support infrared communication.
USART4 supports synchronous mode and a smart card mode conforming to
ISO7816-3.
All information provided in this document is subject to legal disclaimers.
Rev. 4.1 — 15 November 2012
32-bit ARM Cortex-M3 microcontroller
LPC178x/7x
© NXP B.V. 2012. All rights reserved.
53 of 120