C8051F537-ITR Silicon Labs, C8051F537-ITR Datasheet - Page 126
![no-image](/images/no-image-200.jpg)
C8051F537-ITR
Manufacturer Part Number
C8051F537-ITR
Description
8-bit Microcontrollers - MCU 2KB 12ADC 125C 20Pin MCU
Manufacturer
Silicon Labs
Datasheet
1.C8051F536-ITR.pdf
(220 pages)
Specifications of C8051F537-ITR
Product Category
8-bit Microcontrollers - MCU
Rohs
yes
Core
8051
Data Bus Width
8 bit
Maximum Clock Frequency
25 MHz
Program Memory Size
2 KB
Data Ram Size
256 B
On-chip Adc
Yes
Package / Case
TSSOP-20
Mounting Style
SMD/SMT
A/d Bit Size
12 bit
A/d Channels Available
16
Interface Type
SPI, UART
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Number Of Programmable I/os
16
Number Of Timers
3
On-chip Dac
No
Processor Series
C8051
Program Memory Type
Flash
Factory Pack Quantity
2500
Supply Voltage - Max
2.7 V, 5.25 V
Supply Voltage - Min
2 V, 2.7 V
- Current page: 126 of 220
- Download datasheet (2Mb)
C8051F52x/F53x
Important Note: The SPI can be operated in either 3-wire or 4-wire modes, depending on the state of the
NSSMD1–NSSMD0 bits in register SPI0CN. According to the SPI mode, the NSS signal may or may not
be routed to a Port pin.
13.2. Port I/O Initialization
Port I/O initialization consists of the following steps:
1. Select the input mode (analog or digital) for all Port pins, using the Port Input Mode register (PnMDIN).
2. Select the output mode (open-drain or push-pull) for all Port pins, using the Port Output Mode register
(PnMDOUT).
3. Select any pins to be skipped by the I/O Crossbar using the Port Skip registers (PnSKIP).
4. Assign Port pins to desired peripherals using the XBRn registers.
5. Enable the Crossbar (XBARE = 1).
All Port pins must be configured as either analog or digital inputs. Any pins to be used as Comparator or
ADC inputs should be configured as an analog inputs. When a pin is configured as an analog input, its
weak pullup, digital driver, and digital receiver are disabled. This process saves power and reduces noise
on the analog input. Pins configured as digital inputs may still be used by analog peripherals; however, this
practice is not recommended.
Additionally, all analog input pins should be configured to be skipped by the Crossbar (accomplished by
setting the associated bits in PnSKIP). Port input mode is set in the PnMDIN register, where a 1 indicates a
digital input, and a 0 indicates an analog input. All pins default to digital inputs on reset. See SFR Definition
13.4 for the PnMDIN register details.
Important Note: Port 0 and Port 1 pins are 5.25 V tolerant across the operating range of V
.
REGIN
The output driver characteristics of the I/O pins are defined using the Port Output Mode registers (PnMD-
OUT). Each Port Output driver can be configured as either open drain or push-pull. This selection is
required even for the digital resources selected in the XBRn registers, and is not automatic. When the
WEAKPUD bit in XBR1 is 0, a weak pullup is enabled for all Port I/O configured as open-drain. WEAKPUD
does not affect the push-pull Port I/O. Furthermore, the weak pullup is turned off on an output that is driving
a 0 and for pins configured for analog input mode to avoid unnecessary power dissipation.
Registers XBR0 and XBR1 must be loaded with the appropriate values to select the digital I/O functions
required by the design. Setting the XBARE bit in XBR1 to 1 enables the Crossbar. Until the Crossbar is
enabled, the external pins remain as standard Port I/O (in input mode), regardless of the XBRn Register
settings. For given XBRn Register settings, one can determine the I/O pin-out using the Priority Decode
Table.
The Crossbar must be enabled to use Port pins as standard Port I/O in output mode. Port output drivers
are disabled while the Crossbar is disabled.
126
Rev. 1.4
Related parts for C8051F537-ITR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![CP2102EK](/photos/9/3/90395/cp2102ek_tmb.jpg)
Part Number:
Description:
KIT EVALUATION FOR CP2102
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CP2103EK](/photos/9/6/90669/cp2103ek_tmb.jpg)
Part Number:
Description:
KIT EVAL FOR CP2103 USB TO UART
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CP2201EK](/photos/9/9/90977/cp2201ek_tmb.jpg)
Part Number:
Description:
KIT EVAL FOR CP2201 ETH CTRLR
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CAPTOUCHSENSEDC](/photos/9/20/92001/captouchsensedc_tmb.jpg)
Part Number:
Description:
DAUGHTER CARD CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CAPTOUCHSENSESK](/photos/9/20/92002/captouchsensesk_tmb.jpg)
Part Number:
Description:
KIT STARTER CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F320DK](/photos/9/20/92068/c8051f320dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR C8051F320/F321
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F120DK](/photos/9/20/92070/c8051f120dk_tmb.jpg)
Part Number:
Description:
DEVKIT-F120/21/22/23/24/25/26/27
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F310DK](/photos/9/23/92300/c8051f310dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR C8051F310/F311
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F226DK](/photos/9/23/92302/c8051f226dk_tmb.jpg)
Part Number:
Description:
DEV KIT F220/221/226/230/231/236
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F300DK](/photos/9/23/92305/c8051f300dk_tmb.jpg)
Part Number:
Description:
DEV KIT F300/301/302/303/304/305
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F330DK](/photos/9/23/92306/c8051f330dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR C8051F330/F331
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F005DK](/photos/9/23/92307/c8051f005dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR F005/006/007
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F020DK](/photos/9/23/92314/c8051f020dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR F020/F021/F022/F023
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F340DK](/photos/9/23/92323/c8051f340dk_tmb.jpg)
Part Number:
Description:
KIT DEV FOR C8051F34X
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F410DK](/photos/9/23/92324/c8051f410dk_tmb.jpg)
Part Number:
Description:
KIT DEV FOR C8051F41X
Manufacturer:
Silicon Laboratories Inc
Datasheet: