ADP1046DC1-EVALZ Analog Devices, ADP1046DC1-EVALZ Datasheet - Page 54

• Manufacturer Part Number: ADP1046DC1-EVALZ
• Description: Daughter Cards & OEM Boards ADP1046 Daughter Card
• Manufacturer: Analog Devices
• Series: ADP1046r

Specifications of ADP1046DC1-EVALZ

• Rohs: yes
• Product: Daughter Cards
• Description/function: 100 kHz daughter board
• Interface Type: I2C
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 3.3 V
• Factory Pack Quantity: 1
• For Use With: ADP1046

Table 24. Register 0x18—CS2 Value (Output Current)
Bits
[15:4]
[3:0]
Table 25. Register 0x19—CS2 × VS3 Value (Output Power)
Bits
[15:0]
Table 26. Register 0x1A—RTD Temperature Value
Bits
[15:4]
[3:0]
Table 27. Register 0x1B—Read Temperature
Bits
[7:0]
Table 28. Register 0x1C—RTD Offset Trim (MSB)
Bits
[7:2]
1
0
Table 29. Register 0x1D—Share Bus Value
Bits
[7:0]
Table 30. Register 0x1E—Modulation Value
Bits
[7:0]
Table 31. Register 0x1F—Line Impedance Value
Bits
[7:0]
ADP1046
Bit Name
Output current value
Reserved
Bit Name
Output power value
Bit Name
Temperature value
Reserved
Bit Name
Read temperature
Bit Name
Reserved
Trim polarity
RTD offset trim (MSB)
Bit Name
Share bus value
Bit Name
Modulation value
Bit Name
Line impedance value
R/W
R
R
R/W
R
R/W
R
R
R/W
R/W
R/W
R
R/W
R/W
R/W
R
R/W
R
R/W
R
Description
This register contains the 12-bit output current information. This value is the voltage drop
across the sense resistor. To obtain the current value, the user must divide the value of this
register by the sense resistor value (see the CS2+, CS2− Pins section). The CS2± pins have a
full-scale input range of 120 mV or 60 mV (set in Register 0x27[5]). This value has 12 bits of
resolution; the LSB step size depends on the input range value.
When the CS2 input range is set to 120 mV, the LSB step size is 29.30 µV. For example, at
a 30 mV input signal on CS2, the value in this register is 30 mV/29.30 µV = 1024 (0x400).
When the CS2 input range is set to 60 mV, the LSB step size is 14.65 µV. For example, at
a 30 mV input signal on CS2, the value in this register is 30 mV/14.65 µV = 2048 (0x800).
Reserved.
Description
This register contains the 16-bit output power information. This value is the product of the remote
output voltage value (VS3) and the output current reading (CS2). See the Power Readings
section for the formulas needed to convert this digital reading into power information.
Description
This register contains the 12-bit output temperature information, as determined from the
RTD pin. The range of the RTD pin is from 0 V to 1.6 V. This value has 12 bits of resolution,
which results in an LSB size of 390.625 μV. At 0 V input, the value in this register is 0 (0x000).
The recommended nominal voltage at this pin is 1 V. At 1 V input, these bits read 2560 (0xA00).
Reserved.
Description
This register returns an 8-bit temperature in °C (unsigned decimal format). For this feature
to function correctly, the external thermistor must be 100 kΩ with a 16.5 kΩ, 1% resistor in
parallel, and the selected current source must be trimmed to 46 µA by selecting 40 µA in
Register 0x11[7:6] and using the current trim (fine-trim) bits in Register 0x11[5:0].
Description
Reserved.
Setting this bit to 1 means that negative offset is introduced.
Setting this bit to 0 means that positive offset is introduced.
This bit is the MSB of the RTD offset trim. Together with Register 0x20 (the LSBs), this bit sets
the amount of offset trim that is applied to the RTD ADC reading.
Description
This register contains the 8-bit share bus voltage information. If the power supply is the
master, this register outputs 0.
Description
This register contains the 8-bit modulation information. It outputs the amount of
modulation from 0% to 100% that is being placed on the modulating edges.
Description
This register contains the 8-bit line impedance information. This value is (VS2 − VS3)/CS2.
Rev. B | Page 54 of 92
Data Sheet