ADP1046DC1-EVALZ Analog Devices, ADP1046DC1-EVALZ Datasheet - Page 63

no-image

ADP1046DC1-EVALZ

Manufacturer Part Number
ADP1046DC1-EVALZ
Description
Daughter Cards & OEM Boards ADP1046 Daughter Card
Manufacturer
Analog Devices
Series
ADP1046r
Datasheet

Specifications of ADP1046DC1-EVALZ

Rohs
yes
Product
Daughter Cards
Description/function
100 kHz daughter board
Interface Type
I2C
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
3.3 V
Factory Pack Quantity
1
For Use With
ADP1046
Data Sheet
Table 55. Register 0x37—Fast OVP Comparator
Bits
[7:6]
[5:0]
Table 56. Register 0x38—VS1 Trim
Bits
7
[6:0]
Table 57. Register 0x39—VS2 Trim
Bits
7
[6:0]
Table 58. Register 0x3A—VS3 Trim
Bits
7
[6:0]
Bit Name
Fast OVP debounce
Fast OVP threshold
Bit Name
Trim polarity
VS1 trim
Bit Name
Trim polarity
VS2 trim
Bit Name
Trim polarity
VS3 trim
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Description
These bits set the fast OVP debounce time.
Bit 7
0
0
1
1
These bits set the threshold for the fast OVP analog comparator. This threshold is programmable
from 0.8 V to 1.6 V. Setting this value to 0x00 corresponds to a 0.8 V threshold. Setting this value to
0x3F corresponds to a 1.6 V threshold. Each LSB increments the threshold by 12.5 mV. The fast OVP
threshold can be set using the following formula:
Fast_OVP_Threshold = (Bits[5:0] × 0.8 V/63) + 0.8 V
Description
1 = negative gain is introduced.
0 = positive gain is introduced.
These bits set the amount of gain trim that is applied to the VS1 ADC reading. This register trims
the voltage at the VS1 pin for external resistor tolerances. When there is 1 V on the VS1 pin, this
register is trimmed until the VS1 voltage value (Register 0x15[15:4]) reads 2560 (0xA00).
Description
1 = negative gain is introduced.
0 = positive gain is introduced.
These bits set the amount of gain trim that is applied to the VS2 ADC reading. This register trims
the voltage at the VS2 pin for external resistor tolerances. When there is 1 V on the VS2 pin, this
register is trimmed until the VS2 voltage value (Register 0x16[15:4]) reads 2560 (0xA00).
Description
1 = negative gain is introduced.
0 = positive gain is introduced.
These bits set the amount of gain trim that is applied to the VS3 ADC reading. This register trims
the voltage at the VS3 pins for external resistor tolerances. When there is 1 V on each VS3 pin, this
register is trimmed until the VS3 voltage value (Register 0x17[15:4]) reads 2560 (0xA00). The VS3
trim must be performed before the load OVP and load UVP trims are performed.
Bit 6
0
1
0
1
Rev. B | Page 63 of 92
Min
0
0.64
1.92
7.98
Debounce Time (µs)
Typ
0
0.96
2.24
8
Max
0
1.28
2.56
8.32
ADP1046

Related parts for ADP1046DC1-EVALZ