EVAL-ADV7180LFEBZ Analog Devices Inc, EVAL-ADV7180LFEBZ Datasheet - Page 109

• Manufacturer Part Number: EVAL-ADV7180LFEBZ
• Description: BOARD EVAL FOR ADV7180 LFCSP
• Manufacturer: Analog Devices Inc

Specifications of EVAL-ADV7180LFEBZ

• Main Purpose: Video, SDTV Video Decoder - NTSC, PAL, SECAM
• Embedded: No
• Utilized Ic / Part: ADV7180
• Primary Attributes: CVBS (Composite), Y/C (S-video), and YPrPb (Component) Inputs
• Secondary Attributes: 8-bit ITU-R BT.656 YCrCb 4:2:2 Output
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PCB LAYOUT RECOMMENDATIONS
The ADV7180 is a high precision, high speed, mixed-signal
device. To achieve the maximum performance from the part, it
is important to have a well laid out PCB. The following is a
guide for designing a board using the ADV7180.
ANALOG INTERFACE INPUTS
Care should be taken when routing the inputs on the PCB.
Track lengths should be kept to a minimum, and 75 Ω trace
impedances should be used when possible. In addition, trace
impedances other than 75 Ω increase the chance of reflections.
POWER SUPPLY DECOUPLING
It is recommended to decouple each power supply pin with
0.1 μF and 10 nF capacitors. The fundamental idea is to have a
decoupling capacitor within about 0.5 cm of each power pin. In
addition, avoid placing the capacitor on the opposite side of the
PCB from the ADV7180 because doing so interposes resistive
vias in the path. The decoupling capacitors should be located
between the power plane and the power pin. Current should
flow from the power plane to the capacitor and then to the
power pin. Do not apply the power connection between the
capacitor and the power pin. Placing a via underneath the
100 nF capacitor pads, down to the power plane, is the best
approach (see Figure 54).
It is particularly important to maintain low noise and good
stability of P
filtering, and decoupling. It is highly desirable to provide separate
regulated supplies for each of the analog circuitry groups (A
D
Some graphic controllers use substantially different levels of
power when active (during active picture time) and when idle
(during horizontal and vertical sync periods). This can result in
a measurable change in the voltage supplied to the analog supply
regulator, which can in turn produce changes in the regulated
analog supply voltage. This can be mitigated by regulating the
analog supply, or at least P
source, for example, from a 12 V supply.
Using a single ground plane for the entire board is also recom-
mended. This ground plane should have a space between the
analog and digital sections of the PCB (see Figure 55).
VDD
, D
VDDIO
Figure 54. Recommended Power Supply Decoupling
GROUND
VDD
SUPPLY
, and P
. Careful attention must be paid to regulation,
SECTION
ANALOG
VDD
Figure 55. PCB Ground Layout
).
ADV7180
VDD
10nF
, from a different, cleaner power
100nF
SECTION
DIGITAL
VIA TO SUPPLY
VIA TO GND
VDD
Rev. F | Page 109 of 116
,
Experience has repeatedly shown that the noise performance is
the same or better with a single ground plane. Using multiple
ground planes can be detrimental because each separate ground
plane is smaller, and long ground loops can result.
When using separate ground planes is unavoidable, placing a single
ground plane under the ADV7180 is recommended. The location
of the split should be under the ADV7180. In this case, it is even
more important to place components wisely because the current
loops are much longer, and current takes the path of least
resistance. An example of a current loop is a power plane to the
ADV7180 to the digital output trace to the digital data receiver to
the digital ground plane to the analog ground plane.
PLL
Place the PLL loop filter components as close as possible to the
ELPF pin. It should also be placed on the same side of the PCB
as the ADV7180. Do not place any digital or other high frequency
traces near these components. Use the values suggested in this
data sheet with tolerances of 10% or less.
VREFN AND VREFP
The circuit associated with these pins should be placed as close
as possible and on the same side of the PCB as the ADV7180.
DIGITAL OUTPUTS (BOTH DATA AND CLOCKS)
Try to minimize the trace length that the digital outputs have to
drive. Longer traces have higher capacitance, requiring more
current and, in turn, causing more internal digital noise.
Shorter traces reduce the possibility of reflections.
Adding a 30 Ω to 50 Ω series resistor can suppress reflections,
reduce EMI, and reduce the current spikes inside the ADV7180.
If series resistors are used, place them as close as possible to the
ADV7180 pins. However, try not to add vias or extra length to
the output trace to place the resistors closer.
If possible, limit the capacitance that each of the digital outputs
drives to less than 15 pF. This can easily be accomplished by
keeping traces short and by connecting the outputs to only one
device. Loading the outputs with excessive capacitance increases
the current transients inside the ADV7180, creating more digital
noise on its power supplies.
The 40-lead and 32-lead LFCSP have an exposed metal paddle
on the bottom of the package. This paddle must be soldered to
PCB ground for proper heat dissipation and for noise and
mechanical strength benefits.
DIGITAL INPUTS
The digital inputs on the ADV7180 are designed to work with
1.8 V to 3.3 V signals and are not tolerant of 5 V signals. Extra
components are needed if 5 V logic signals are required to be
applied to the decoder.
ADV7180