ATMEGA328P-AU Atmel, ATMEGA328P-AU Datasheet - Page 304

MCU AVR 32K FLASH 32TQFP

ATMEGA328P-AU

Manufacturer Part Number
ATMEGA328P-AU
Description
MCU AVR 32K FLASH 32TQFP
Manufacturer
Atmel
Series
AVR® ATmegar

Specifications of ATMEGA328P-AU

Core Processor
AVR
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
23
Program Memory Size
32KB (16K x 16)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
32-TQFP, 32-VQFP
Processor Series
ATMEGA32x
Core
AVR8
Data Bus Width
8 bit
Data Ram Size
2 KB
Interface Type
2-Wire, SPI, USART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
23
Number Of Timers
3
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 8 Channel
Cpu Family
ATmega
Device Core
AVR
Device Core Size
8b
Frequency (max)
20MHz
Total Internal Ram Size
2KB
# I/os (max)
23
Number Of Timers - General Purpose
3
Operating Supply Voltage (typ)
2.5/3.3/5V
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
1.8V
Instruction Set Architecture
RISC
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
32
Package Type
TQFP
Controller Family/series
AVR MEGA
No. Of I/o's
23
Eeprom Memory Size
1KB
Ram Memory Size
2KB
Cpu Speed
20MHz
Rohs Compliant
Yes
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVR
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
ATMEGA328P-20AU
ATMEGA328P-20AU
Q3790246

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA328P-AU
Manufacturer:
KINGBRIGHT
Quantity:
37 000
Part Number:
ATMEGA328P-AU
Manufacturer:
ATMEL
Quantity:
1 250
Part Number:
ATMEGA328P-AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATMEGA328P-AU
Manufacturer:
AT
Quantity:
1 000
Part Number:
ATMEGA328P-AU
Manufacturer:
AT
Quantity:
400
Part Number:
ATMEGA328P-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATMEGA328P-AU
Manufacturer:
MICROCHIP/微芯
Quantity:
2 000
Company:
Part Number:
ATMEGA328P-AU
Quantity:
3 268
Company:
Part Number:
ATMEGA328P-AU
Quantity:
6 688
Part Number:
ATMEGA328P-AUR
Manufacturer:
Atmel
Quantity:
10 000
27.7
27.7.1
27.7.2
8271C–AVR–08/10
Parallel Programming
Enter Programming Mode
Considerations for Efficient Programming
Table 27-16. Command Byte Bit Coding
The following algorithm puts the device in Parallel (High-voltage) Programming mode:
1. Set Prog_enable pins listed in
2. Apply 4.5 - 5.5V between V
Ensure that V
3. Wait 20 - 60 µs, and apply 11.5 - 12.5V to RESET.
4. Keep the Prog_enable pins unchanged for at least 10µs after the High-voltage has been
5. Wait at least 300 µs before giving any parallel programming commands.
6. Exit Programming mode by power the device down or by bringing RESET pin to 0V.
If the rise time of the V
tive algorithm can be used.
1. Set Prog_enable pins listed in
2. Apply 4.5 - 5.5V between V
3. Monitor V
4. Keep the Prog_enable pins unchanged for at least 10µs after the High-voltage has been
5. Wait until V
6. Exit Programming mode by power the device down or by bringing RESET pin to 0V.
The loaded command and address are retained in the device during programming. For efficient
programming, the following should be considered.
• The command needs only be loaded once when writing or reading multiple memory locations.
• Skip writing the data value 0xFF, that is the contents of the entire EEPROM (unless the
• Address high byte needs only be loaded before programming or reading a new 256 word
ATmega48A/48PA/88A/88PA/168A/168PA/328/328
EESAVE Fuse is programmed) and Flash after a Chip Erase.
window in Flash or 256 byte EEPROM. This consideration also applies to Signature bytes
reading.
Command Byte
V
applied to ensure the Prog_enable Signature has been latched.
V
applied to ensure the Prog_enable Signature has been latched.
commands.
CC
CC
0000 1000
0000 0100
0000 0010
0000 0011
to 0V.
to 0V.
CC
CC
CC
, and as soon as V
reaches at least 1.8V within the next 20 µs.
actually reaches 4.5 -5.5V before giving any parallel programming
Command Executed
Read Signature Bytes and Calibration byte
Read Fuse and Lock bits
Read Flash
Read EEPROM
CC
is unable to fulfill the requirements listed above, the following alterna-
CC
CC
Table 27-14 on page 303
and GND.
Table 27-14 on page 303
and GND.
CC
reaches 0.9 - 1.1V, apply 11.5 - 12.5V to RESET.
to “0000”, RESET pin to 0V and
to “0000”, RESET pin to 0V and
304

Related parts for ATMEGA328P-AU