LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 437

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
UM10237_4
User manual
4.12 UARTn Fractional Divider Register (U0FDR - 0xE000 C028, U2FDR -
4.11 IrDA Control Register for UART3 Only (U3ICR - 0xE007 C024)
The IrDA Control Register enables and configures the IrDA mode for UART3 only. The
value of U3ICR should not be changed while transmitting or receiving data, or data loss or
corruption may occur.
Table 390. IrDA Control Register for UART3 only (U3ICR - address 0xE007 C024) bit
The PulseDiv bits in U3ICR are used to select the pulse width when the fixed pulse width
mode is used in IrDA mode (IrDAEn = 1 and FixPulseEn = 1). The value of these bits
should be set so that the resulting pulse width is at least 1.63 µs.
possible pulse widths.
Table 391. IrDA Pulse Width
0xE007 8028, U3FDR - 0xE007 C028)
The UART0/2/3 Fractional Divider Register (U0/2/3FDR) controls the clock pre-scaler for
the baud rate generation and can be read and written at the user’s discretion. This
pre-scaler takes the APB clock and generates an output clock according to the specified
fractional requirements.
Important: If the fractional divider is active (DIVADDVAL > 0) and DLM = 0, the value of
the DLL register must be 3 or greater.
Bit
0
1
2
5:3
31:6 -
FixPulseEn
0
1
1
1
1
1
1
1
1
Symbol
IrDAEn
IrDAInv
FixPulseEn
PulseDiv
description
Value Description
0
1
NA
Rev. 04 — 26 August 2009
IrDA mode on UART3 is disabled, UART3 acts as a
standard UART.
IrDA mode on UART3 is enabled.
When 1, the serial input is inverted. This has no effect
on the serial output. When 0, the serial input is not
inverted.
When 1, enabled IrDA fixed pulse width mode.
Configures the pulse when FixPulseEn = 1. See text
below for details.
Reserved, user software should not write ones to
reserved bits. The value read from a reserved bit is
not defined.
PulseDiv
x
0
1
2
3
4
5
6
7
IrDA Transmitter Pulse width (µs)
3 / (16 × baud rate)
2 × T
4 × T
8 × T
16 × T
32 × T
64 × T
128 × T
256 × T
Chapter 16: LPC24XX UART0/2/3
PCLK
PCLK
PCLK
PCLK
PCLK
PCLK
PCLK
PCLK
Table 16–391
UM10237
© NXP B.V. 2009. All rights reserved.
Reset value
0
0
0
0
0
shows the
437 of 792