PIC18F458T-I/PT Microchip Technology, PIC18F458T-I/PT Datasheet - Page 143

• Manufacturer Part Number: PIC18F458T-I/PT
• Description: IC MCU FLASH 16KX16 W/CAN 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F458T-I/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

16.5.8
The following steps should be taken when configuring
the ECCP1 module for PWM operation:
1.
TABLE 16-5:
© 2006 Microchip Technology Inc.
INTCON
RCON
IPR2
PIR2
PIE2
TMR2
PR2
T2CON
TRISD
ECCPR1H
ECCPR1L
ECCP1CON EPWM1M1 EPWM1M0
ECCPAS
ECCP1DEL
Legend:
Name
Configure the PWM module:
a)
b)
c)
d)
e)
Disable the ECCP1/P1A, P1B, P1C and/or
P1D outputs by setting the respective TRISD
bits.
Set the PWM period by loading the PR2
register.
Set the PWM duty cycle by loading the
ECCPR1L register and ECCP1CON<5:4>
bits.
Configure the ECCP1 module for the
desired PWM operation by loading the
ECCP1CON register with the appropriate
value. With the ECCP1M<3:0> bits, select
the active-high/low levels for each PWM
output. With the EPWM1M<1:0> bits, select
one of the available output modes.
For Half-Bridge Output mode, set the dead-
band delay by loading the ECCP1DEL
register with the appropriate value.
x = unknown, u = unchanged, - = unimplemented, read as ‘0’. Shaded cells are not used by the ECCP module.
SETUP FOR PWM OPERATION
Timer2 Module Register
Timer2 Module Period Register
PORTD Data Direction Register
Enhanced Capture/Compare/PWM Register 1 High Byte
Enhanced Capture/Compare/PWM Register 1 Low Byte
ECCPASE
GIE/GIEH
EPDC7
IPEN
Bit 7
—
—
—
—
REGISTERS ASSOCIATED WITH ENHANCED PWM AND TIMER2
PEIE/GIEL
ECCPAS2
TOUTPS3
EPDC6
CMIP
CMIF
CMIE
Bit 6
—
TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000
ECCPAS1 ECCPAS0 PSSAC1
TMR0IE
EDC1B1
EPDC5
Bit 5
—
—
—
—
EDC1B0 ECCP1M3 ECCP1M2 ECCP1M1 ECCP1M0 0000 0000 0000 0000
EPDC4
INT0IE
EEIP
EEIE
Bit 4
EEIF
RI
EPDC3
BCLIP
BCLIF
BCLIE
RBIE
Bit 3
TO
2.
3.
PSSAC0
TMR0IF
EPDC2
LVDIP
LVDIF
LVDIE
Configure and start TMR2:
a)
b)
c)
Enable PWM outputs after a new cycle has
started:
a)
b)
Bit 2
PD
Clear the TMR2 interrupt flag bit by clearing
the TMR2IF bit in the PIR1 register.
Set the TMR2 prescale value by loading the
T2CKPS bits (T2CON<1:0>).
Enable Timer2 by setting the TMR2ON bit
(T2CON<2>) register.
Wait until TMR2 overflows (TMR2IF bit
becomes a ‘1’). The new PWM cycle begins
here.
Enable the ECCP1/P1A, P1B, P1C and/or
P1D pin outputs by clearing the respective
TRISD bits.
PSSBD1
TMR3IP
TMR3IF
TMR3IE
EPDC1
INT0IF
Bit 1
POR
ECCP1IP -1-1 1111 -1-1 1111
ECCP1IE -0-0 0000 -0-0 0000
ECCP1IF -0-0 0000 -0-0 0000
PSSBD0 0000 0000 0000 0000
EPDC0
RBIF
PIC18FXX8
Bit 0
BOR
0000 000x 0000 000u
0--1 110q 0--0 011q
0000 0000 0000 0000
1111 1111 1111 1111
1111 1111 1111 1111
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
0000 0000 uuuu uuuu
POR, BOR
Value on
DS41159E-page 141
Value on
all other
Resets