PIC24FJ256DA206-I/PT Microchip Technology, PIC24FJ256DA206-I/PT Datasheet - Page 212

• Manufacturer Part Number: PIC24FJ256DA206-I/PT
• Description: MCU PIC 16BIT FLASH 256K 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ256DA206-I/PT

• Core Size: 16-Bit
• Program Memory Size: 256KB (85.5K x 24)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, GFX, LVD, POR, PWM, WDT
• Number Of I /o: 52
• Program Memory Type: FLASH
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC24
• No. Of I/o's: 52
• Ram Memory Size: 96KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Interface: I2C, SPI, UART, USB
• Embedded Interface Type: I2C, SPI, UART, USB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC24FJ256DA210 FAMILY
To set up the SPI module for the Standard Master mode
of operation:
1.
2.
3.
4.
5.
FIGURE 15-1:
DS39969B-page 212
If using interrupts:
a)
b)
c)
Write the desired settings to the SPIxCON1
and
(SPIxCON1<5>) = 1.
Clear the SPIROV bit (SPIxSTAT<6>).
Enable SPI operation by setting the SPIEN bit
(SPIxSTAT<15>).
Write the data to be transmitted to the SPIxBUF
register. Transmission (and reception) will start
as soon as data is written to the SPIxBUF
register.
SSx/FSYNCx
SCKx
SDOx
SDIx
Clear the SPIxIF bit in the respective IFS
register.
Set the SPIxIE bit in the respective IEC
register.
Write the SPIxIP bits in the respective IPC
register to set the interrupt priority.
SPIxCON2
Read SPIxBUF
Control
Sync
SPIx MODULE BLOCK DIAGRAM (STANDARD MODE)
Transfer
registers
bit 0
SPIxBUF
with
SPIxSR
Control
Clock
Shift Control
MSTEN
Transfer
Write SPIxBUF
Select
Edge
To set up the SPI module for the Standard Slave mode
of operation:
1.
2.
3.
4.
5.
6.
7.
16
Clear the SPIxBUF register.
If using interrupts:
a)
b)
c)
Write the desired settings to the SPIxCON1
and
(SPIxCON1<5>) = 0.
Clear the SMP bit.
If the CKE bit (SPIxCON1<8>) is set, then the
SSEN bit (SPIxCON1<7>) must be set to enable
the SSx pin.
Clear the SPIROV bit (SPIxSTAT<6>).
Enable SPI operation by setting the SPIEN bit
(SPIxSTAT<15>).
Clear the SPIxIF bit in the respective IFS
register.
Set the SPIxIE bit in the respective IEC
register.
Write the SPIxIP bits in the respective IPC
register to set the interrupt priority.
Secondary
1:1 to 1:8
Prescaler
SPIxCON2
Internal Data Bus
 2010 Microchip Technology Inc.
1:1/4/16/64
registers
Prescaler
Primary
SPIxCON1<1:0>
SPIxCON1<4:2>
Enable
Master Clock
with
F
CY
MSTEN