PIC24FJ256DA206-I/PT Microchip Technology, PIC24FJ256DA206-I/PT Datasheet - Page 226

• Manufacturer Part Number: PIC24FJ256DA206-I/PT
• Description: MCU PIC 16BIT FLASH 256K 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ256DA206-I/PT

• Core Size: 16-Bit
• Program Memory Size: 256KB (85.5K x 24)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, GFX, LVD, POR, PWM, WDT
• Number Of I /o: 52
• Program Memory Type: FLASH
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC24
• No. Of I/o's: 52
• Ram Memory Size: 96KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Interface: I2C, SPI, UART, USB
• Embedded Interface Type: I2C, SPI, UART, USB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC24FJ256DA210 FAMILY
REGISTER 16-1:
DS39969B-page 226
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
I2CEN
GCEN
R/W-0
R/W-0
I2CEN: I2Cx Enable bit
1 = Enables the I2Cx module and configures the SDAx and SCLx pins as serial port pins
0 = Disables the I2Cx module. All I
Unimplemented: Read as ‘0’
I2CSIDL: Stop in Idle Mode bit
1 = Discontinues module operation when device enters an Idle mode
0 = Continues module operation in Idle mode
SCLREL: SCLx Release Control bit (when operating as I
1 = Releases SCLx clock
0 = Holds SCLx clock low (clock stretch)
If STREN = 1:
Bit is R/W (i.e., software may write ‘0’ to initiate stretch and write ‘1’ to release clock). Hardware is clear
at the beginning of slave transmission. Hardware is clear at the end of slave reception.
If STREN = 0:
Bit is R/S (i.e., software may only write ‘1’ to release clock). Hardware clear at beginning of slave
transmission.
IPMIEN: Intelligent Platform Management Interface (IPMI) Enable bit
1 = IPMI Support mode is enabled; all addresses are Acknowledged
0 = IPMI mode is disabled
A10M: 10-Bit Slave Addressing bit
1 = I2CxADD is a 10-bit slave address
0 = I2CxADD is a 7-bit slave address
DISSLW: Disable Slew Rate Control bit
1 = Slew rate control disabled
0 = Slew rate control enabled
SMEN: SMBus Input Levels bit
1 = Enables I/O pin thresholds compliant with SMBus specifications
0 = Disables the SMBus input thresholds
GCEN: General Call Enable bit (when operating as I
1 = Enables interrupt when a general call address is received in the I2CxRSR (module is enabled for
0 = General call address disabled
STREN: SCLx Clock Stretch Enable bit (when operating as I
Used in conjunction with the SCLREL bit.
1 = Enables software or receive clock stretching
0 = Disables software or receive clock stretching
STREN
R/W-0
reception)
U-0
—
I2CxCON: I2Cx CONTROL REGISTER
HC = Hardware Clearable bit
W = Writable bit
‘1’ = Bit is set
I2CSIDL
ACKDT
R/W-0
R/W-0
R/W-1, HC
R/W-0, HC
SCLREL
ACKEN
2
C™ pins are controlled by port functions
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0, HC
IPMIEN
R/W-0
RCEN
2
C slave)
2
C slave)
R/W-0, HC
2
C slave)
R/W-0
A10M
PEN
 2010 Microchip Technology Inc.
x = Bit is unknown
R/W-0, HC
DISSLW
R/W-0
RSEN
R/W-0, HC
SMEN
R/W-0
SEN
bit 8
bit 0