CS1W-CN224 Omron, CS1W-CN224 Datasheet - Page 40

• Manufacturer Part Number: CS1W-CN224
• Description: "CABLE,CS1/C200H PRO27,2m"
• Manufacturer: Omron

Specifications of CS1W-CN224

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

CPU Rack
A CPU Rack consists of a Duplex CPU Backplane to which CPU Units,
Power Supply Units, a Duplex Unit, CS1-series Basic I/O Units, CS1-
series Special I/O Units, and CS1-series CPU Bus Units are mounted.
Memory Cards and Inner Boards to mount in the CPU Units are
optional. (Inner Board cannot be mounted to the CS1D-CPU@@H/P)
The CPU Units, Power Supply Units, Duplex CPU Backplane, and
Duplex Unit are all designed specifically for CS1D PLCs.
Note: Different Backplanes are used for the CPU Rack and Expansion
Expansion Racks
An Expansion Rack consists of an Expansion Backplane to which
Power Supply Units, CS1-series Basic I/O Units, CS1-series Special I/
O Units, and CS1-series CPU Bus Units are mounted.
The Power Supply Units and Expansion Backplane are designed spe-
cifically for CS1D PLCs.
CS1-series Expansion Backplanes and C200H Backplanes cannot be
connected.
286
System Configuration (Duplex Systems)
Racks. Be sure to use the correct Backplane.
Duplex-CPU System
Single-CPU System
Duplex CPU Backplane
CS1D-BC052 (See note.)
Duplex CPU Backplane
CS1D-BC082S (See note.)
Up to 5 Units can be mounted.
CS1-series Basic I/O Units
CS1-series Special I/O Units
CS1-series CPU Bus Units
Note: C200H Units cannot be mounted.
Up to 8 Units can be mounted.
CS1-series Basic I/O Units
CS1-series Special I/O Units
CS1-series CPU Bus Units
Note: C200H Units cannot be mounted.
Duplex (DPL) Unit
CS1D-DPL01
SYSMAC
CS1D-CPU67H
PROGRAMMABLE CONTROLLER
PERIPHERAL
OPEN
MCPWR
PORT
ERR/ALM
PRPHL
CS1D CPU Units for
Duplex-CPU System
CS1D-CPU65H/67H/65P/67P
RUN
Duplex CPU Units
INH
CS1D CPU Units for
Single-CPU System
CS1D-CPU42S/44S/65S/67S
BUSY
BKUP
COMM
DPL01
DUPLEX
L
R
INIT.
LEFT CPU
RIGHT CPU
DPL STATUS
ACTIVE
CPU STATUS
ACTIVE
CPU STATUS
DPL SW
ON
ON
SW
USE
NO USE
USE
NO USE
ACT.
LEFT
PRPHL
COMM
A39512
RSV
ON
SPL
ACT.
RIGHT
OFF
DPL
Long-distance Expansion Racks
A Long-distance Expansion Rack consists of an Expansion Backplane
to which an I/O Interface Unit, CS1-series Basic I/O Units, CS1-series
Special I/O Units, and CS1-series CPU Bus Units are mounted. An I/O
Control Unit is used to connect to the Long-distance Expansion Racks.
Using Long-distance Expansion Rack increases the normal limit of
12 m for the Rack to 50 m.
CS1D PLCs
With a CS1D Duplex-CPU System, two CPU Units can be mounted to
the CPU Rack for Duplex Mode operation (Duplex Mode), or just one
CPU Unit can be mounted for Simplex Mode operation. In either case,
a Duplex Unit is required.
With a CS1D Single-CPU System, just one CPU Unit is mounted and a
Duplex Unit is not required.
Also, two Power Supply Units can be mounted to any Rack to increase
redundancy. (Racks can also be operated with only one Power Supply
Unit.) With any of these combinations, there are no further restrictions
if the system configuration, e.g., the same number of Expansion Racks
can be used as with the other CS1-series PLCs.
Note: C200H Basic I/O Units, C200H Special I/O Units, and C200H
SYSMAC
CS1D-CPU67H
PROGRAMMABLE CONTROLLER
SYSMAC
CS1D-CPU67S
PROGRAMMABLE CONTROLLER
PERIPHERAL
PERIPHERAL
OPEN
OPEN
MCPWR
MCPWR
PORT
PORT
ERR/ALM
ERR/ALM
CPU Bus Units cannot be mounted on any Rack.
PRPHL
PRPHL
RUN
RUN
INH
INH
BUSY
BUSY
BKUP
COMM
BKUP
COMM
Duplex Power Supply Units
Duplex Power Supply Units
CS1D Power Supply Units
CS1D-PA207R/PD024
CS1D Power Supply Units
CS1D-PA207R/PD024
CS1D CPU Rack
CS1D CPU Rack
Programmable Controllers