TMP89xy60UG/FG Toshiba, TMP89xy60UG/FG Datasheet - Page 398

• Manufacturer Part Number: TMP89xy60UG/FG
• Manufacturer: Toshiba

Specifications of TMP89xy60UG/FG

• Package: LQFP64/QFP64
• Rom Types (m=mask,p=otp,f=flash): M/F
• Rom Size: 32/60
• Ram Size: 3K
• Driver Led: 8
• Driver Lcd: -
• Spi/sio Channels: -
• Uart/sio Channels: 2
• I2c/sio Channels: 1
• High-speed Serial Output: -
• Adc 8-bit Channels: -
• Adc 10-bit Channels: 16
• Da Converter Channels: -
• Timer Counter 18-bit Channel: -
• Timer Counter 16-bit Channel: 2
• Timer Counter 8-bit Channel: 4
• Motor Channels: -
• Watchdog Timer: Y
• Dual Clock: Y
• Clock Gear: Y
• Number Of I/o Ports: 58
• Power Supply (v): 4.3 to 5.5

22.12
Security
RA003
22.12.3
Table 22-22 Option Codes
string authentication is performed or not when executing the flash memory erase command and whether the
security program is checked or not when starting OCD can be designated.
EPFC_OP
DAFC_OP
Symbol
If a specified option code is placed at a specified address inside the interrupt vector area, whether password
Option codes
-
-
Erase password free code EPFC_OP (0xFFFA)
a password may get lost. In this case, you can cancel the password string authentication of the flash
memory erase command (0xF0) by setting the erase password free code (EPFC_OP). EPFC_OP is
assigned to 0xFFFA in the vector area. Allocate 0xFF to this EPFC_OP to cancel the password string
of the flash memory erase command (0xF0).
be enabled during mass production by allocating data other than 0xFF to EPFC_OP.
command. If Sector Erase is executed with EPFC_OP set to 0xFF, the TMP89FS60 goes into an idle
state. Commands other than the flash memory erase command cannot cancel the password string au-
thentication.
OCD security program free code DAFC_OP (0xFFFB)
third party. If the security program is enabled, restrictions are imposed on operation commands related
to memory access, and the startup of OCD.
that the OCD may be used by keeping the contents of memory intact, it is possible to directly start the
OCD by setting the OCD security program free code (DAFC_OP) and thereby skipping the security
program check (the password string authentication, however, is still required).
of the OCD, assign 0xFF to DAFC_OP. In this case, the security program check is not performed, and
the OCD can be started by performing only the password string authentication.
security program. If the OCD is started with the security program enabled, the TMP89FS60 stops
communication and goes into an idle state. To use the OCD when the TMP89FS60 is in this idle state,
Chip Erase must be executed for flash memory by using the flash memory erase command (0xF0). If
the security program is disabled, the OCD can be started by performing only the password string au-
thentication.
Password string authentication when the flash
memory erase command is executed
Security program check when the OCD is star-
ted
If changes are frequently made to a program during software development, there are cases in which
It is recommended that the password string authentication of the flash memory erase command (0xF0)
Only Chip Erase can cancel the password string authentication by using the flash memory erase
With the TMP89FS60, you can enable the security program to prevent illegal access attempts by a
The security program should be usually enabled at the time of shipment. If there is the possibility
DAFC_OP is assigned to 0xFFFB in the vector area. To skip the security program check at the startup
If DAFC_OP is not 0xFF, whether the OCD can be used or not is determined by the status of the
Function
Page 382
Address
0xFFFA
0xFFFB
0xFF : The password string authentication is skipped
(only PNSA and PCSA are authenticated).
Other than 0xFF: The password string, PNSA, and
PCSA are authenticated.
0xFF: The security program check is skipped.
Other than 0xFF: The security program check is per-
formed.
Set value
TMP89FS60