S9S12GN16F0CFT Freescale Semiconductor, S9S12GN16F0CFT Datasheet - Page 296

• Manufacturer Part Number: S9S12GN16F0CFT
• Description: 16-bit Microcontrollers - MCU 16-bit16k Flash 2k RAM
• Manufacturer: Freescale Semiconductor

Specifications of S9S12GN16F0CFT

• Rohs: yes
• Core: S12
• Processor Series: MC9S12G
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 25 MHz
• Program Memory Size: 16 KB
• Data Ram Size: 1024 B
• On-chip Adc: Yes
• Operating Supply Voltage: 3.13 V to 5.5 V
• Operating Temperature Range: - 40 C to + 85 C
• Package / Case: TSSOP-20
• Mounting Style: SMD/SMT

Background Debug Module (S12SBDMV1)
enabled just for the READ_BD and WRITE_BD access cycle. This allows the BDM to access BDM
locations unobtrusively, even if the addresses conflict with the application memory map.
7.4.4
BDM firmware commands are used to access and manipulate CPU resources. The system must be in active
BDM to execute standard BDM firmware commands, see
Normal instruction execution is suspended while the CPU executes the firmware located in the standard
BDM firmware lookup table. The hardware command BACKGROUND is the usual way to activate BDM.
As the system enters active BDM, the standard BDM firmware lookup table and BDM registers become
visible in the on-chip memory map at 0x3_FF00–0x3_FFFF, and the CPU begins executing the standard
BDM firmware. The standard BDM firmware watches for serial commands and executes them as they are
received.
The firmware commands are shown in
298
BACKGROUND
ACK_ENABLE
ACK_DISABLE
READ_BD_BYTE
READ_BD_WORD
READ_BYTE
READ_WORD
WRITE_BD_BYTE
WRITE_BD_WORD
WRITE_BYTE
WRITE_WORD
NOTE:
If enabled, ACK will occur when data is ready for transmission for all BDM READ commands and will occur after the write is
complete for all BDM WRITE commands.
Command
Standard BDM Firmware Commands
Opcode
(hex)
CC
EC
D5
D6
E4
E0
E8
C4
C0
C8
90
16-bit address
16-bit data out
16-bit address
16-bit data out
16-bit address
16-bit data out
16-bit address
16-bit data out
16-bit address
16-bit address
16-bit address
16-bit address
16-bit data in
16-bit data in
16-bit data in
16-bit data in
None
None
None
Data
MC9S12G Family Reference Manual,
Table 7-5. Hardware Commands
Table
Enter background mode if BDM is enabled. If enabled, an ACK will be issued
when the part enters active background mode.
Enable Handshake. Issues an ACK pulse after the command is executed.
Disable Handshake. This command does not issue an ACK pulse.
Read from memory with standard BDM firmware lookup table in map.
Odd address data on low byte; even address data on high byte.
Read from memory with standard BDM firmware lookup table in map.
Must be aligned access.
Read from memory with standard BDM firmware lookup table out of map.
Odd address data on low byte; even address data on high byte.
Read from memory with standard BDM firmware lookup table out of map.
Must be aligned access.
Write to memory with standard BDM firmware lookup table in map.
Odd address data on low byte; even address data on high byte.
Write to memory with standard BDM firmware lookup table in map.
Must be aligned access.
Write to memory with standard BDM firmware lookup table out of map.
Odd address data on low byte; even address data on high byte.
Write to memory with standard BDM firmware lookup table out of map.
Must be aligned access.
7-6.
Section 7.4.2, “Enabling and Activating
Rev.1.23
Description
Freescale Semiconductor
BDM”.