LTC3735EUHF Linear Technology, LTC3735EUHF Datasheet - Page 11

• Manufacturer Part Number: LTC3735EUHF
• Description: IC CTRLR DC/DC 2PH HI EFF 38-QFN
• Manufacturer: Linear Technology

Specifications of LTC3735EUHF

• Applications: Controller, Intel Mobile CPU
• Number Of Outputs: 1
• Voltage - Output: 0.7 ~ 1.71 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 38-QFN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Voltage - Input: -

OPERATIO
Output Voltage at Start-Up and at Deeper Sleep State
Under normal conditions, the output voltage of the regu-
lator is commanded by six VID bits, except at start-up and
at deeper sleep state. At start-up, the RUN/SS capacitor
starts to charge up and its voltage limits the inrush current
from the input power source. This linearly rising current
limit provides a controlled output voltage rise. During
start-up, the VID command is ignored and the output set
point is determined by the value of the resistor connected
to the RBOOT pin. The VID bits continue to be ignored for
15 switching cycles after the completion of the following
two conditions: 1) output voltage has risen up and has
regulated 2) MCH_PG signal has asserted. After 15 switch-
ing cycles, output voltage is fully commanded by VID bits.
In deeper sleep state, the VID command and STP_CPUB
signal are ignored and the output set point is determined
by the parallel value of the resistors at the RDPRSLP pin
and RDPSLP pin.
Operational Amplifier and Deep Sleep Offset
The internal operational amplifier provides a program-
mable output offset at deep sleep state (when the
STP_CPUB signal is low). The offset percentage is pro-
grammed by the resistor from RDPSLP to V
resistor from output to V
slew rate of 5V/μs and is capable of driving capacitive
loads with an output RMS current typically up to 40mA.
The open-loop gain of the amplifier is >120dB and the
unity-gain bandwidth is 2MHz.
Output Overvoltage Protection
An overvoltage comparator, OV, guards against transient
overshoots (>10%) as well as other more serious condi-
tions that may overvoltage the output. In this case, the top
MOSFET is turned off and the bottom MOSFET is turned on
until the overvoltage condition is cleared.
U
(Refer to Functional Diagram)
OA
+
. The amplifier has an output
OA
+
and the
Power Good
The PGOOD pin is connected to the drain of an internal
N-channel MOSFET. The MOSFET turns on when the
output voltage is not within ±10% of its nominal set point.
When the output voltage is within ±10% of its nominal set
point, the MOSFET turns off and PGOOD is high imped-
ance. PGOOD monitors the V
is not asserted. During VID, deep sleep or deeper sleep
transitions, PGOOD is masked from going low for 110μs,
preventing the system from resetting during CPU mode
changes. When VID bits, STP_CPUB or DPRSLPVR sig-
nals change again after a previous transition, but before
the timer expires, the internal timer resets.
Short-Circuit Detection
The RUN/SS capacitor is used initially to limit the inrush
current from the input power source. Once the control-
lers have been given time, as determined by the capacitor
on the RUN/SS pin, to charge up the output capacitors
and provide full-load current, the RUN/SS capacitor is
then used as a short-circuit timeout circuit. If the output
voltage falls to less than 70% of its nominal output
voltage the RUN/SS capacitor begins discharging as-
suming that the output is in a severe overcurrent and/or
short-circuit condition. If the condition lasts for a long
enough period as determined by the size of the RUN/SS
capacitor, the controller will be shut down until the
RUN/SS pin voltage is recycled. This built-in latchoff can
be overidden by providing a current >5μA to the RUN/SS
pin. This current shortens the soft-start period but also
prevents net discharge of the RUN/SS capacitor during a
severe overcurrent and/or short-circuit condition. Fold-
back current limiting is activated when the output voltage
falls below 70% of its nominal level whether or not the
short-circuit latchoff circuit is enabled.
BOOT
voltage when MCH_PG
LTC3735
11
3735f