ATMEGA324PV-10AU Atmel, ATMEGA324PV-10AU Datasheet - Page 147

• Manufacturer Part Number: ATMEGA324PV-10AU
• Description: IC MCU AVR 32K FLASH 44-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA324PV-10AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire/JTAG/SPI/USART
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Package: 44TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 10 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Controller Family/series: AVR MEGA
• No. Of I/o's: 32
• Eeprom Memory Size: 1KB
• Ram Memory Size: 2KB
• Cpu Speed: 10MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP44 - STK600 SOCKET/ADAPTER 44-TQFPATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

14.7.4
8011O–AVR–07/10
Phase Correct PWM Mode
A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by set-
ting OC2x to toggle its logical level on each compare match (COM2x1:0 = 1). The waveform
generated will have a maximum frequency of f
ture is similar to the OC2A toggle in CTC mode, except the double buffer feature of the Output
Compare unit is enabled in the fast PWM mode.
The phase correct PWM mode (WGM22:0 = 1 or 5) provides a high resolution phase correct
PWM waveform generation option. The phase correct PWM mode is based on a dual-slope
operation. The counter counts repeatedly from BOTTOM to TOP and then from TOP to BOT-
TOM. TOP is defined as 0xFF when WGM22:0 = 1, and OCR2A when MGM22:0 = 5. In non-
inverting Compare Output mode, the Output Compare (OC2x) is cleared on the compare match
between TCNT2 and OCR2x while upcounting, and set on the compare match while downcount-
ing. In inverting Output Compare mode, the operation is inverted. The dual-slope operation has
lower maximum operation frequency than single slope operation. However, due to the symmet-
ric feature of the dual-slope PWM modes, these modes are preferred for motor control
applications.
In phase correct PWM mode the counter is incremented until the counter value matches TOP.
When the counter reaches TOP, it changes the count direction. The TCNT2 value will be equal
to TOP for one timer clock cycle. The timing diagram for the phase correct PWM mode is shown
on
the dual-slope operation. The diagram includes non-inverted and inverted PWM outputs. The
small horizontal line marks on the TCNT2 slopes represent compare matches between OCR2x
and TCNT2.
Figure 14-7. Phase Correct PWM Mode, Timing Diagram
The Timer/Counter Overflow Flag (TOV2) is set each time the counter reaches BOTTOM. The
Interrupt Flag can be used to generate an interrupt each time the counter reaches the BOTTOM
value.
Figure
TCNTn
OCnx
OCnx
Period
14-7. The TCNT2 value is in the timing diagram shown as a histogram for illustrating
1
2
oc2
= f
ATmega164P/324P/644P
clk_I/O
/2 when OCR2A is set to zero. This fea-
3
OCnx Interrupt Flag Set
OCRnx Update
TOVn Interrupt Flag Set
(COMnx1:0 = 2)
(COMnx1:0 = 3)
147