ATMEGA324PV-10AU Atmel, ATMEGA324PV-10AU Datasheet - Page 37

• Manufacturer Part Number: ATMEGA324PV-10AU
• Description: IC MCU AVR 32K FLASH 44-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA324PV-10AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire/JTAG/SPI/USART
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Package: 44TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 10 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Controller Family/series: AVR MEGA
• No. Of I/o's: 32
• Eeprom Memory Size: 1KB
• Ram Memory Size: 2KB
• Cpu Speed: 10MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP44 - STK600 SOCKET/ADAPTER 44-TQFPATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6.7
6.8
8011O–AVR–07/10
128 kHz Internal Oscillator
External Clock
The 128 kHz internal Oscillator is a low power Oscillator providing a clock of 128 kHz. The fre-
quency is nominal at 3V and 25°C. This clock may be select as the system clock by
programming the CKSEL Fuses to “0011” as shown in
Table 6-12.
Note:
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 6-13.
To drive the device from an external clock source, XTAL1 should be driven as shown in
6-3. To run the device on an external clock, the CKSEL Fuses must be programmed to “0000”.
Figure 6-3.
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 6-14.
BOD enabled
Fast rising power
Slowly rising power
Power Conditions
6-13.
6-15.
1. Note that the 128 kHz oscillator is a very low power clock source, and is not designed for high
accuracy.
128 kHz Internal Oscillator Operating Modes
Start-up Times for the 128 kHz Internal Oscillator
External Clock Drive Configuration
Crystal Oscillator Clock Frequency
Nominal Frequency
Nominal Frequency
0 - 20 MHz
EXTERNAL
128 kHz
SIGNAL
CLOCK
Start-up Time from Power-
down and Power-save
NC
Reserved
6 CK
6 CK
6 CK
ATmega164P/324P/644P
XTAL2
XTAL1
GND
Table
(2)
Additional Delay from
6-12.
14CK + 64 ms
14CK + 4 ms
Reset
14CK
CKSEL3..0
CKSEL3..0
0011
0000
SUT1..0
00
01
10
11
Figure
37