PXAS37KBA,512 NXP Semiconductors, PXAS37KBA,512 Datasheet - Page 30

IC XA MCU 16BIT 32K OTP 68-PLCC

PXAS37KBA,512

Manufacturer Part Number
PXAS37KBA,512
Description
IC XA MCU 16BIT 32K OTP 68-PLCC
Manufacturer
NXP Semiconductors
Series
XAr
Datasheet

Specifications of PXAS37KBA,512

Core Processor
XA
Core Size
16-Bit
Speed
30MHz
Connectivity
EBI/EMI, I²C, UART/USART
Peripherals
PWM, WDT
Number Of I /o
50
Program Memory Size
32KB (32K x 8)
Program Memory Type
OTP
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x8b
Oscillator Type
External
Operating Temperature
0°C ~ 70°C
Package / Case
68-PLCC
Processor Series
PXAS3x
Core
80C51
Data Bus Width
16 bit
Data Ram Size
1 KB
Interface Type
I2C, UART
Maximum Clock Frequency
30 MHz
Number Of Programmable I/os
50
Number Of Timers
3
Operating Supply Voltage
2.7 V to 5.5 V
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
0 C
On-chip Adc
8 bit, 8 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
 Details
Other names
568-3536-5
935262377512
PXAS37KBA

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PXAS37KBA,512
Manufacturer:
TI
Quantity:
5
Part Number:
PXAS37KBA,512
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
PXAS37KBA,512
Manufacturer:
NXP USA Inc.
Quantity:
269
Philips Semiconductors
1100 0001 since a 1 in bit 0 will exclude slave 0. Both slaves can be
selected at the same time by an address which has bit 0 = 0 (for
slave 0) and bit 1 = 0 (for slave 1). Thus, both could be addressed
with 1100 0000.
In a more complex system the following could be used to select
slaves 1 and 2 while excluding slave 0:
Slave 0
Slave 1
Slave 2
2000 Dec 01
XA 16-bit microcontroller
32 K/1 K OTP/ROM/ROMless, 8-channel 8-bit A/D, low voltage (2.7 V–5.5 V),
I
SnCON
Bit Addressable
Reset Value: 00H
2
BIT
SnCON.5 SM2
SnCON.4 REN
SnCON.3 TB8
SnCON.2 RB8
SnCON.1 TI
SnCON.0 RI
C, 2 UARTs, 16 MB address range
Address:
SADDR =
SADEN =
Given
SADDR =
SADEN =
Given
SADDR =
SADEN =
Given
SYMBOL FUNCTION
=
=
=
S0CON 420
S1CON 424
Enables the multiprocessor communication feature in Modes 2 and 3. In Mode 2 or 3, if SM2 is set to 1, then RI
will not be activated if the received 9th data bit (RB8) is 0. In Mode 1, if SM2=1 then RI will not be activated if a
valid stop bit was not received. In Mode 0, SM2 should be 0.
Enables serial reception. Set by software to enable reception. Clear by software to disable reception.
The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired. The TB8 bit is not
double buffered. See text for details.
In Modes 2 and 3, is the 9th data bit that was received. In Mode 1, if SM2=0, RB8 is the stop bit that was
received. In Mode 0, RB8 is not used.
Transmit interrupt flag. Set when another byte may be written to the UART transmitter. See text for details.
Must be cleared by software.
Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the end of the stop bit time
in the other modes (except see SM2). Must be cleared by software.
1100 0000
1111 1001
1100 0XX0
1110 0000
1111 1010
1110 0X0X
1110 0000
1111 1100
1110 00XX
Where SM0, SM1 specify the serial port mode, as follows:
SM0
0
0
1
1
Figure 21. Serial Port Control (SnCON) Register
SM1
0
1
0
1
MSB
SM0
Mode
3
0
1
2
SM1
shift register
8-bit UART
9-bit UART
9-bit UART
Description
30
SM2
uniquely addressed by 1110 0110. Slave 1 requires that bit 1 = 0 and
In the above example the differentiation among the 3 slaves is in the
lower 3 address bits. Slave 0 requires that bit 0 = 0 and it can be
it can be uniquely addressed by 1110 and 0101. Slave 2 requires
that bit 2 = 0 and its unique address is 1110 0011. To select Slaves 0
and 1 and exclude Slave 2 use address 1110 0100, since it is
necessary to make bit 2 = 1 to exclude slave 2.
The Broadcast Address for each slave is created by taking the
logical OR of SADDR and SADEN. Zeros in this result are teated as
don’t-cares. In most cases, interpreting the don’t-cares as ones, the
broadcast address will be FF hexadecimal.
Upon reset SADDR and SADEN are loaded with 0s. This produces
a given address of all “don’t cares” as well as a Broadcast address
of all “don’t cares”. This effectively disables the Automatic
Addressing mode and allows the microcontroller to use standard
UART drivers which do not make use of this feature.
REN
Baud Rate
f
variable
f
variable
OSC
OSC
/16
/32
TB8
RB8
TI
Preliminary specification
RI
LSB
XA-S3
SU00597C