ATTINY24-15SSZ Atmel, ATTINY24-15SSZ Datasheet - Page 55

• Manufacturer Part Number: ATTINY24-15SSZ
• Description: MCU AVR 2K FLASH 15MHZ 14-SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY24-15SSZ

• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 12
• Eeprom Size: 128 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Program Memory Size: 2KB (2K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: USI
• Core Size: 8-Bit
• Cpu Family: ATtiny
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Interface Type: SPI/UART
• Total Internal Ram Size: 128Byte
• # I/os (max): 12
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 14
• Package Type: SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12. I/O Ports
12.1
7701D–AVR–09/10
Overview
All Atmel
I/O ports. This means that the SBI and CBI instructions can be used to change direction of one
port pin without unintentionally changing the direction of any other pin. The same applies when
changing drive value (if configured as output) or enabling/disabling of pull-up resistors (if con-
figured as input). Each output buffer has symmetrical drive characteristics with both high sink
and source capability. The pin driver is strong enough to drive LED displays directly. All port
pins have individually selectable pull-up resistors with a supply-voltage invariant resistance.
All I/O pins have protection diodes to both VCC and Ground as indicated in
page
Figure 12-1. I/O Pin Equivalent Schematic
All registers and bit references in this section are written in general form. A lower case “x” rep-
resents the numbering letter for the port, and a lower case “n” represents the bit number.
However, when using the register or bit defines in a program, the precise form must be used.
For example, PORTB3 for bit no. 3 in Port B, here documented generally as PORTxn. The
physical I/O Registers and bit locations are listed in
as system clock.” on page
Three I/O memory address locations are allocated for each port, one each for the data register
(PORTx), data direction register (DDRx), and the port input pins (PINx). The port input pins I/O
location is read only, while the data register and the data direction register are read/write.
However, writing a logical one to a bit in the PINx register, will result in a toggle in the corre-
sponding bit in the data register. In addition, the pull-up disable (PUD) bit in the MCUCR
disables the pull-up function for all pins in all ports when set.
Using the I/O port as General Digital I/O is described in
56. Most port pins are multiplexed with alternate functions for the peripheral features on the
device. How each alternate function interferes with the port pin is described in
Functions” on page
alternate functions.
55. See
®
AVR
Pxn
“Electrical Characteristics” on page 177
®
ports have true read-modify-write functionality when used as general digital
60. Refer to the individual module sections for a full description of the
69.
Atmel ATtiny24/44/84 [Preliminary]
C
pin
“EXT_CLOCK = external clock is selected
for a complete list of parameters.
“Ports as General Digital I/O” on page
"General Digital I/O" for
See Figure
R
Details
pu
Logic
Figure 12-1 on
“Alternate Port
55