AT32UC3L064-AUT Atmel, AT32UC3L064-AUT Datasheet - Page 292

• Manufacturer Part Number: AT32UC3L064-AUT
• Description: MCU AVR32 64KB FLASH 48TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3L064-AUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: SPI/TWI/USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL
• Development Tools By Supplier: AT32UC3L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 9-ch x 10-bit
• Package: 48TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 50 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Figure 16-2. Timing Diagram, Synchronous Interrupts, High Level or Rising Edge
Figure 16-3. Timing Diagram, Synchronous Interrupts, Low Level or Falling Edge
16.6.3
16.6.4
32099F–11/2010
EXTINTn/NMI
EXTINTn/NMI
Non-Maskable Interrupt
Asynchronous Interrupts
FILTER off
FILTER on
FILTER off
FILTER on
ISR.INTn:
ISR.INTn:
ISR.INTn:
ISR.INTn:
CLK_SYNC
CLK_SYNC
The NMI supports the same features as the external interrupts, and is accessed through the
same registers. The description in
instead of the INTn bits.
The NMI is non-maskable within the CPU in the sense that it can interrupt any other execution
mode. Still, as for the other external interrupts, the actual NMI input can be enabled and disabled
by accessing the registers in the EIC.
Each external interrupt can be made asynchronous by writing a one to INTn in the ASYNC reg-
ister. This will route the interrupt signal through the asynchronous path of the module. All edge
interrupts will be interpreted as level interrupts and the filter is disabled. If an interrupt is config-
ured as edge triggered interrupt in asynchronous mode, a zero in EDGE.INTn will be interpreted
as low level, and a one in EDGE.INTn will be interpreted as high level.
EIC_WAKE will be set immediately after the source triggers the interrupt, while the correspond-
ing bit in ISR and the interrupt to the interrupt controller will be set on the next rising edge of
CLK_SYNC. Please refer to
Figure 16-4 on page 293
Section 16.6.1
should be followed, accessing the NMI bit
for details.
AT32UC3L016/32/64
292