AT32UC3L064-AUT Atmel, AT32UC3L064-AUT Datasheet - Page 595

• Manufacturer Part Number: AT32UC3L064-AUT
• Description: MCU AVR32 64KB FLASH 48TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3L064-AUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: SPI/TWI/USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL
• Development Tools By Supplier: AT32UC3L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 9-ch x 10-bit
• Package: 48TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 50 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Table 25-3.
Table 25-4.
25.4.2
25.4.3
32099F–11/2010
Generator
AST
Generator
PWMA channel 0
Peripheral Event Connections
Low Power Operation
Peripheral Event Mapping from AST
Peripheral Event Mapping from PWMA
Generated Event
Overflow event
Periodic event
Alarm event
Overflow event
Periodic event
Alarm event
Overflow event
Periodic event
Alarm event
Generated Event
Timebase counter
reaches the duty cycle
value.
Each generated peripheral event is connected to one or more users. If a peripheral event is con-
nected to multiple users, the peripheral event can trigger actions in multiple modules.
A peripheral event user can likewise be connected to one or more peripheral event generators. If
a peripheral event user is connected to multiple generators, the peripheral events are OR’ed
together to a single peripheral event. This means that peripheral events from either one of the
generators will result in a peripheral event to the user.
To configure a peripheral event, the peripheral event must be enabled at both the generator and
user side. Even if a generator is connected to multiple users, only the users with the peripheral
event enabled will trigger on the peripheral event.
As the peripheral events do not require CPU intervention, they are available in Idle mode. They
are also available in deeper sleep modes if both the generator and user remain clocked in that
mode.
Certain events are known as asynchronous peripheral events, as identified in
Table
user peripherals. The clock will be restarted for this module only, without waking the system from
sleep mode. The clock remains active only as long as required by the triggered function, before
being switched off again, and the system remains in the original sleep mode. The CPU and sys-
25-4. These can be issued even when the system clock is stopped, and revive unclocked
User
ACIFB
ADCIFB
CAT
User
ACIFB
ADCIFB
Effect
Comparison is triggered if the ACIFB.CONFn
register is written to 11 (Event Triggered Single
Measurement Mode) and the EVENTEN bit in
the ACIFB.CTRL register is written to 1.
Conversion is triggered if the TRGMOD bit in
the ADCIFB.TRGR register is written to 111
(Peripheral Event Trigger).
Trigger one iteration of autonomous touch
detection.
Effect
Comparison is triggered if the ACIFB.CONFn
register is written to 11 (Event Triggered Single
Measurement Mode) and the EVENTEN bit in
the ACIFB.CTRL register is written to 1.
Conversion is triggered if the TRGMOD bit in
the ADCIFB.TRGR register is written to 111
(Peripheral Event Trigger).
AT32UC3L016/32/64
Asynchronous
Yes
Asynchronous
No
Table 25-1
595
to