ATMEGA64A-AU Atmel, ATMEGA64A-AU Datasheet - Page 56
![MCU AVR 64K ISP FLASH 64-TQFP](/photos/12/13/121332/313-64-tqfp_sml.jpg)
ATMEGA64A-AU
Manufacturer Part Number
ATMEGA64A-AU
Description
MCU AVR 64K ISP FLASH 64-TQFP
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheets
1.ATMEGA64A-MUR.pdf
(21 pages)
2.ATMEGA64A-AU.pdf
(392 pages)
3.ATMEGA64A-AU.pdf
(3 pages)
Specifications of ATMEGA64A-AU
Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
53
Program Memory Size
64KB (32K x 16)
Program Memory Type
FLASH
Eeprom Size
2K x 8
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-TQFP, 64-VQFP
Package
64TQFP
Device Core
AVR
Family Name
ATmega
Maximum Speed
16 MHz
Operating Supply Voltage
3.3|5 V
Data Bus Width
8 Bit
Number Of Programmable I/os
53
Interface Type
SPI/USART
On-chip Adc
8-chx10-bit
Number Of Timers
4
Processor Series
ATMEGA64x
Core
AVR8
Data Ram Size
4 KB
Maximum Clock Frequency
16 MHz
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
Minimum Operating Temperature
- 40 C
Cpu Family
ATmega
Device Core Size
8b
Frequency (max)
16MHz
Total Internal Ram Size
4KB
# I/os (max)
53
Number Of Timers - General Purpose
4
Operating Supply Voltage (typ)
3.3/5V
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
2.7V
Instruction Set Architecture
RISC
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
64
Package Type
TQFP
For Use With
770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATMEGA64A-AU
Manufacturer:
ATMEL
Quantity:
4 500
Company:
Part Number:
ATMEGA64A-AU
Manufacturer:
Atmel
Quantity:
900
Company:
Part Number:
ATMEGA64A-AU
Manufacturer:
ATMEL85
Quantity:
900
Part Number:
ATMEGA64A-AU
Manufacturer:
AT
Quantity:
20 000
10.3
10.3.1
10.3.2
8160C–AVR–07/09
Timed Sequences for Changing the Configuration of the Watchdog Timer
Safety Level 0
Safety Level 1
Table 10-1.
Figure 10-7. Watchdog Timer
The sequence for changing configuration differs slightly between the three safety levels. Sepa-
rate procedures are described for each level.
This mode is compatible with the Watchdog operation found in ATmega103. The Watchdog
Timer is initially disabled, but can be enabled by writing the WDE bit to 1 without any restriction.
The Time-out period can be changed at any time without restriction. To disable an enabled
Watchdog Timer, the procedure described on
In this mode, the Watchdog Timer is initially disabled, but can be enabled by writing the WDE bit
to 1 without any restriction. A timed sequence is needed when changing the Watchdog Time-out
period or disabling an enabled Watchdog Timer. To disable an enabled Watchdog Timer, and/or
changing the Watchdog Time-out, the following procedure must be followed:
1. In the same operation, write a logic one to WDCE and WDE. A logic one must be written
2. Within the next four clock cycles, in the same operation, write the WDE and WDP bits as
M103C
Unprogrammed
Unprogrammed
Programmed
Programmed
to WDE regardless of the previous value of the WDE bit.
desired, but with the WDCE bit cleared.
WDT Configuration as a Function of the Fuse Settings of M103C and WDTON
WDTON
Unprogrammed
Programmed
Unprogrammed
Programmed
OSCILLATOR
WATCHDOG
Safety
Level
1
2
0
2
page 57
WDT Initial
State
Disabled
Enabled
Disabled
Enabled
(WDE bit description) must be followed.
How to Disable
the WDT
Timed
sequence
Always enabled
Timed
sequence
Always enabled
ATmega64A
How to Change
Time-out
Timed sequence
Timed sequence
No restriction
Timed sequence
56