ATMEGA644V-10MU Atmel, ATMEGA644V-10MU Datasheet - Page 125

• Manufacturer Part Number: ATMEGA644V-10MU
• Description: IC AVR MCU FLASH 64K 44-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA644V-10MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-VQFN Exposed Pad
• Package: 44QFN EP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 10 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 32
• Interface Type: JTAG/SPI/TWI/USART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Ram Size: 4 KB
• Maximum Clock Frequency: 20 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600-TQFP44 - STK600 SOCKET/ADAPTER 44-TQFPATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

14.11 Register Description
14.11.1
2593N–AVR–07/10
TCCR1A – Timer/Counter1 Control Register A
Figure 14-13. Timer/Counter Timing Diagram, with Prescaler (f
• Bit 7:6 – COMnA1:0: Compare Output Mode for Channel A
• Bit 5:4 – COMnB1:0: Compare Output Mode for Channel B
The COMnA1:0 and COMnB1:0 control the Output Compare pins (OCnA and OCnB respec-
tively) behavior. If one or both of the COMnA1:0 bits are written to one, the OCnA output
overrides the normal port functionality of the I/O pin it is connected to. If one or both of the
COMnB1:0 bit are written to one, the OCnB output overrides the normal port functionality of the
I/O pin it is connected to. However, note that the Data Direction Register (DDR) bit correspond-
ing to the OCnA or OCnB pin must be set in order to enable the output driver.
When the OCnA or OCnB is connected to the pin, the function of the COMnx1:0 bits is depen-
dent of the WGMn3:0 bits setting.
WGMn3:0 bits are set to a Normal or a CTC mode (non-PWM).
Table 14-2.
Bit
(0x80)
Read/Write
Initial Value
COMnA1/COMnB1
and ICF n
(PC and PFC PWM)
TOVn
(CTC and FPWM)
(Update at TOP)
0
0
1
1
TCNTn
TCNTn
OCRnx
(clk
as TOP)
clk
clk
I/O
(FPWM)
I/O
Tn
/8)
(if used
COM1A1
Compare Output Mode, non-PWM
R/W
7
0
COM1A0
COMnA0/COMnB0
R/W
6
0
TOP - 1
TOP - 1
Old OCRnx Value
0
1
0
1
COM1B1
R/W
Table 14-2
5
0
COM1B0
R/W
4
0
Description
Normal port operation, OCnA/OCnB disconnected.
Toggle OCnA/OCnB on Compare Match.
Clear OCnA/OCnB on Compare Match (Set output to
low level).
Set OCnA/OCnB on Compare Match (Set output to
high level).
shows the COMnx1:0 bit functionality when the
TOP
TOP
R
3
–
0
BOTTOM
TOP - 1
clk_I/O
R
2
–
0
New OCRnx Value
/8)
WGM11
R/W
1
0
ATmega644
BOTTOM + 1
TOP - 2
WGM10
R/W
0
0
TCCR1A
125