ATMEGA644V-10MU Atmel, ATMEGA644V-10MU Datasheet - Page 273

• Manufacturer Part Number: ATMEGA644V-10MU
• Description: IC AVR MCU FLASH 64K 44-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA644V-10MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-VQFN Exposed Pad
• Package: 44QFN EP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 10 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 32
• Interface Type: JTAG/SPI/TWI/USART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Ram Size: 4 KB
• Maximum Clock Frequency: 20 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600-TQFP44 - STK600 SOCKET/ADAPTER 44-TQFPATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

24.6
2593N–AVR–07/10
Entering the Boot Loader Program
Table 24-2.
Note:
Table 24-3.
Note:
Entering the Boot Loader takes place by a jump or call from the application program. This may
be initiated by a trigger such as a command received via USART, or SPI interface. Alternatively,
the Boot Reset Fuse can be programmed so that the Reset Vector is pointing to the Boot Flash
start address after a reset. In this case, the Boot Loader is started after a reset. After the applica-
tion code is loaded, the program can start executing the application code. Note that the fuses
cannot be changed by the MCU itself. This means that once the Boot Reset Fuse is pro-
grammed, the Reset Vector will always point to the Boot Loader Reset and the fuse can only be
changed through the serial or parallel programming interface.
Table 24-4.
Note:
BLB0 Mode
BLB1 Mode
BOOTRST
1
2
3
4
1
2
3
4
1
0
1. “1” means unprogrammed, “0” means programmed
1. “1” means unprogrammed, “0” means programmed
1. “1” means unprogrammed, “0” means programmed
Boot Lock Bit0 Protection Modes (Application Section)
Boot Lock Bit1 Protection Modes (Boot Loader Section)
Boot Reset Fuse
BLB02
BLB12
Reset Address
Reset Vector = Application Reset (address 0x0000)
Reset Vector = Boot Loader Reset (see
1
1
0
0
1
1
0
0
BLB01
BLB11
1
0
0
1
1
0
0
1
(1)
Protection
No restrictions for SPM or (E)LPM accessing the Application
section.
SPM is not allowed to write to the Application section.
SPM is not allowed to write to the Application section, and
(E)LPM executing from the Boot Loader section is not allowed to
read from the Application section. If Interrupt Vectors are placed
in the Boot Loader section, interrupts are disabled while
executing from the Application section.
(E)LPM executing from the Boot Loader section is not allowed to
read from the Application section. If Interrupt Vectors are placed
in the Boot Loader section, interrupts are disabled while
executing from the Application section.
Protection
No restrictions for SPM or (E)LPM accessing the Boot Loader
section.
SPM is not allowed to write to the Boot Loader section.
SPM is not allowed to write to the Boot Loader section, and
(E)LPM executing from the Application section is not allowed to
read from the Boot Loader section. If Interrupt Vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
(E)LPM executing from the Application section is not allowed to
read from the Boot Loader section. If Interrupt Vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
Table 24-7 on page
(1)
(1)
280)
ATmega644
273