MCF5216CVF66 Freescale Semiconductor, MCF5216CVF66 Datasheet - Page 383

• Manufacturer Part Number: MCF5216CVF66
• Description: IC MPU 32BIT COLDF 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF521xr

Specifications of MCF5216CVF66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 142
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• Ram Memory Size: 64KB
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Operating Temperature Range: -40°C To +85°C
• No. Of Pins: 256
• Rohs Compliant: No
• Package: 256MA-BGA
• Device Core: ColdFire
• Family Name: MCF521x
• Maximum Speed: 66 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 142
• Interface Type: QSPI/UART/I2C/CAN
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 8
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

20.5.16 Pulse Accumulator Flag Register (GPTPAFLG)
Freescale Semiconductor
Bit(s)
Bit(s)
7–2
1
0
1
0
Address
When the fast flag clear all enable bit, GPTSCR1[TFFCA], is set, any access
to the pulse accumulator counter registers clears all the flags in GPTPAFLG.
Reset
Field
R/W
PAOVF
PAOVI
Name
Name
PAIF
PAI
—
Figure 20-18. Pulse Accumulator Flag Register (GPTPAFLG)
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
Table 20-18. GPTPACTL Field Descriptions (continued)
7
Pulse accumulator overflow interrupt enable. Enables the PAOVF flag to generate
interrupt requests.
1 PAOVF interrupt requests enabled
0 PAOVF interrupt requests disabled
Pulse accumulator input interrupt enable. Enables the PAIF flag to generate interrupt
requests.
1 PAIF interrupt requests enabled
0 PAIF interrupt requests disabled
Reserved, should be cleared.
Pulse accumulator overflow flag. Set when the 16-bit pulse accumulator rolls over from
0xFFFF to 0x0000. If the GPTPACTL[PAOVI] bit is also set, PAOVF generates an
interrupt request. Clear PAOVF by writing a 1 to it. This bit is read anytime, write
anytime. (Writing 1 clears the flag; writing 0 has no effect.)
1 Pulse accumulator overflow
0 No pulse accumulator overflow
Pulse accumulator input flag. Set when the selected edge is detected at the PAI pin.
In event counter mode, the event edge sets PAIF. In gated time accumulation mode,
the trailing edge of the gate signal at the PAI pin sets PAIF. If the PAI bit in GPTPACTL
is also set, PAIF generates an interrupt request. Clear PAIF by writing a 1 to it.
1 Active PAI input
0 No active PAI input
Table 20-19. GPTPAFLG Field Descriptions
IPSBAR + 0x1A_0019, 0x1B_0019
—
NOTE
0000_0000
R/W
Description
Description
General Purpose Timer Modules (GPTA and GPTB)
2
PAOVF
1
PAIF
0
20-15