XR17V354IB176-F Exar Corporation, XR17V354IB176-F Datasheet - Page 60

• Manufacturer Part Number: XR17V354IB176-F
• Description: IC UART PCIE 256B DUAL 176FPBGA
• Manufacturer: Exar Corporation

Specifications of XR17V354IB176-F

• Number Of Channels: 4, QUART
• Package / Case: 176-LFBGA
• Features: *
• Fifo's: 256 Byte
• Protocol: RS485
• Voltage - Supply: 3.3V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 25 Mbps
• Supply Current: 120 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3.3 V
• No. Of Channels: 4
• Uart Features: Tx/Rx FIFO Counters
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: BGA
• No. Of Pins: 176
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

XR17V354
HIGH PERFORMANCE QUAD PCI-EXPRESS UART
Enhanced features are enabled or disabled using this register. Bits [3:0] provide single or dual consecutive
character software flow control selection (see
are selected, the double 8-bit words are concatenated into two sequential characters. Caution: note that
whenever changing the TX or RX flow control bits, always reset all bits back to logic 0 (disable) before
programming a new setting.
EFR[7]: Auto CTS Flow Control Enable
Automatic CTS or DSR Flow Control.
•
•
EFR[6]: Auto RTS or DTR Flow Control Enable
RTS#/DTR# output may be used for hardware flow control by setting EFR bit [6] to logic 1. When Auto RTS/
DTR is selected, an interrupt will be generated when the receive FIFO is filled to the programmed trigger level
and RTS/DTR# will de-assert (HIGH) at the next upper trigger or selected hysteresis level. RTS/DTR# will re-
assert (LOW) when FIFO data falls below the next lower trigger or selected hysteresis level (see FCTR bits 4-
7). The RTS# or DTR# output must be asserted (LOW) before the auto RTS/DTR can take effect. The selection
for RTS# or DTR# is through MCR bit [2]. RTS/DTR# pin will function as a general purpose output when
hardware flow control is disabled.
•
•
EFR[5]: Special Character Detect Enable
•
•
EFR[4]: Enhanced Function Bits Enable
Enhanced function control bit. This bit enables the enhanced functions in IER bits [7:5], ISR bits [5:4], FCR
bits [5:4], MCR bits [7:5] and MSR [7:0] bits to be modified. After modifying any enhanced bits, EFR bit [4] can
be set to a logic 0 to latch the new values. This feature prevents legacy software from altering or overwriting
the enhanced functions once set. Normally, it is recommended to leave it enabled.
•
•
4.14
Logic 0 = Automatic CTS/DSR flow control is disabled (default).
Logic 1 = Enable Automatic CTS/DSR flow control. Transmission stops when CTS/DSR# pin de-asserts
(HIGH). Transmission resumes when CTS/DSR# pin is asserted (LOW). The selection for CTS# or DSR# is
through MCR bit [2].
Logic 0 = Automatic RTS/DTR flow control is disabled (default).
Logic 1 = Enable Automatic RTS/DTR flow control.
Logic 0 = Special Character Detect Disabled (default).
Logic 1 = Special Character Detect Enabled. The UART compares each incoming receive character with
data in Xoff-2 register. If a match exists, the received data will be transferred to FIFO and ISR bit [4] will be
set to indicate detection of the special character. bit [0] corresponds with the LSB bit for the receive
character. If flow control is set for comparing Xon1, Xoff1 (EFR [1:0]=10) then flow control and special
character work normally. However, if flow control is set for comparing Xon2, Xoff2 (EFR[1:0]=01) then flow
control works normally, but Xoff2 will not go to the FIFO, and will generate an Xoff interrupt and a special
character interrupt.
Logic 0 = Disable write access to the enhanced function bits: IER bits [7:5], ISR bits [5:4], FCR bits [5:4],
MCR bits [7:5] and MSR [7:0] bits. After a reset, all these bits are set to a logic 0 to be compatible with
ST16C550 mode (default).
Logic 1 = Enables write access to the enhanced function bits: IER bits [7:5], ISR bits [5:4], FCR bits [5:4],
MCR bits [7:5] and MSR [7:0] bits.
Enhanced Feature Register (EFR) - Read/Write
Table
20). When the Xon1 and Xon2 and Xoff1 and Xoff2 modes
60
REV. 1.0.1