DP83848VYB National Semiconductor, DP83848VYB Datasheet - Page 38

• Manufacturer Part Number: DP83848VYB
• Description: TRANSCEIVER, ENET PHY, 10/100, 48LQFP
• Manufacturer: National Semiconductor

Specifications of DP83848VYB

• Data Rate: 100Mbps
• No. Of Ports: 1
• Ethernet Type: IEEE 802.3u
• Supply Current: 92mA
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -40°C To +105°C
• Digital Ic Case Style: LQFP
• No.: RoHS Compliant
• Interface Type: MII Serial, RMII
• Rohs Compliant: Yes
• Lead Free Status / Rohs Status: Not Compliant

www.national.com
10:7
6:0
Bit
Bit
15
14
13
12
11
7.1.2 Basic Mode Status Register (BMSR)
6
5
4
3
2
1
0
7
AUTO-NEGOTIATION
AUTO-NEGOTIATION
JABBER DETECT
REMOTE FAULT
COLLISION TEST
MF PREAMBLE
SUPPRESSION
HALF DUPLEX
HALF DUPLEX
FULL DUPLEX
FULL DUPLEX
LINK STATUS
100BASE-TX
100BASE-TX
100BASE-T4
CAPABILITY
RESERVED
COMPLETE
EXTENDED
10BASE-T
10BASE-T
RESERVED
Bit Name
ABILITY
Bit Name
TABLE 13. Basic Mode Status Register (BMSR), address 0x01h
0, RO/LH
0, RO/LH
0, RO/LL
0, RO/P
1, RO/P
1, RO/P
1, RO/P
1, RO/P
1, RO/P
1, RO/P
1, RO/P
Default
0, RO
0, RO
Default
0, RW
0, RO
100BASE-T4 Capable:
0 = Device not able to perform 100BASE-T4 mode.
100BASE-TX Full Duplex Capable:
1 = Device able to perform 100BASE-TX in full duplex mode.
100BASE-TX Half Duplex Capable:
1 = Device able to perform 100BASE-TX in half duplex mode.
10BASE-T Full Duplex Capable:
1 = Device able to perform 10BASE-T in full duplex mode.
10BASE-T Half Duplex Capable:
1 = Device able to perform 10BASE-T in half duplex mode.
RESERVED: Write as 0, read as 0.
Preamble suppression Capable:
1 = Device able to perform management transaction with preamble suppressed, 32-bits
of preamble needed only once after reset, invalid opcode or invalid turnaround.
0 = Normal management operation.
Auto-Negotiation Complete:
1 = Auto-Negotiation process complete.
0 = Auto-Negotiation process not complete.
Remote Fault:
1 = Remote Fault condition detected (cleared on read or by reset). Fault criteria: Far
End Fault Indication or notification from Link Partner of Remote Fault.
0 = No remote fault condition detected.
Auto Negotiation Ability:
1 = Device is able to perform Auto-Negotiation.
0 = Device is not able to perform Auto-Negotiation.
Link Status:
1 = Valid link established (for either 10 or 100 Mb/s operation).
0 = Link not established.
The criteria for link validity is implementation specific. The occurrence of a link failure
condition will causes the Link Status bit to clear. Once cleared, this bit may only be set
by establishing a good link condition and a read via the management interface.
Jabber Detect: This bit only has meaning in 10 Mb/s mode.
1 = Jabber condition detected.
0 = No Jabber.
This bit is implemented with a latching function, such that the occurrence of a jabber
condition causes it to set until it is cleared by a read to this register by the management
interface or by a reset.
Extended Capability:
1 = Extended register capabilities.
0 = Basic register set capabilities only.
Collision Test:
1 = Collision test enabled.
0 = Normal operation.
When set, this bit will cause the COL signal to be asserted in response to the assertion
of TX_EN within 512-bit times. The COL signal will be de-asserted within 4-bit times
in response to the de-assertion of TX_EN.
RESERVED: Write ignored, read as 0.
38
Description
Description