ADSP-BF504BCPZ-3F Analog Devices Inc, ADSP-BF504BCPZ-3F Datasheet - Page 30

• Manufacturer Part Number: ADSP-BF504BCPZ-3F
• Description: Blackfin W/Processor & Executable Flash
• Manufacturer: Analog Devices Inc
• Series: Blackfin®r
• Type: Fixed Pointr

Specifications of ADSP-BF504BCPZ-3F

• Interface: CAN, EBI/EMI, I²C, IrDA, PPI, SPI, SPORT, UART/USART
• Clock Rate: 300MHz
• Non-volatile Memory: FLASH (16MB)
• On-chip Ram: 68kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.29V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: *
• Package / Case: *
• Rohs Compliant: YES
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADSP-BF504/ADSP-BF504F/ADSP-BF506F
PROCESSOR—ABSOLUTE MAXIMUM RATINGS
Stresses greater than those listed in
nent damage to the device. These are stress ratings only.
Functional operation of the device at these or any other condi-
tions greater than those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device
reliability.
Table 20.
1
2
3
4
Table 21. Maximum Duty Cycle for Input Transient Voltage
1
2
3
Parameter
Internal Supply Voltage (V
External (I/O) Supply Voltage (V
Input Voltage
Input Voltage
Output Voltage Swing
I
Storage Temperature Range
Junction Temperature While Biased
(Non-Automotive Models)
Junction Temperature While Biased
(Automotive Models)
V
–0.50
–0.70
–0.80
–0.90
–1.00
Applies to 100% transient duty cycle. For other duty cycles see
Applies only when V
Applies to pins SCL and SDA.
For more information, see description preceding
Applies to all signal pins with the exception of CLKIN, XTAL, EXT_WAKE.
The individual values cannot be combined for analysis of a single instance of
Duty cycle refers to the percentage of time the signal exceeds the value for the
OH
fications, the range is V
overshoot or undershoot. The worst case observed value must fall within one of
the voltages specified, and the total duration of the overshoot or undershoot
(exceeding the 100% case) must be less than or equal to the corresponding duty
cycle.
100% case. The is equivalent to the measured duration of a single instance of
overshoot or undershoot as a percentage of the period of occurrence.
IN
/I
Min (V)
OL
Current per Pin Group
2
1, 2
1, 2, 3
DDEXT
V
+3.80
+4.00
+4.10
+4.20
+4.30
IN
DDEXT
Max (V)
is within specifications. When V
± 0.2 V.
DDINT
4
2
)
DDEXT
Maximum Duty Cycle
100%
40%
25%
15%
10%
Table 20
)
Rating
–0.3 V to +1.5 V
–0.3 V to +3.8 V
–0.5 V to +3.6 V
–0.5 V to +5.5 V
–0.5 V to
76 mA (max)
–65
+110
+125
Table
V
DDEXT
°
C to +150
may cause perma-
°
°
22.
C
C
+0.5 V
DDEXT
Rev. 0 | Page 30 of 80 | December 2010
Table
is outside speci-
°
C
21.
3
1
Table 22
rent for a group of pins. Permanent damage can occur if this
value is exceeded. To understand this specification, if pins PG5,
PG6, PG7, PG8, and PG9 from group 5 in the
Groups
total current for those pins would be 10 mA. This would allow
up to 66 mA total that could be sourced or sunk by the remain-
ing pins in the group without damaging the device. For a list of
all groups and their pins, see the
table. Note that the V
per-pin maximum current requirements, see the
Electrical Characteristics
Table 22. Total Current Pin Groups
Group
1
2
3
4
5
6
7
8
9
10
table, each were sourcing or sinking 2 mA each, the
specifies the maximum total source/sink (I
Pins in Group
PF10, PF11
PF12, PF13, PF14, PF15
PG0
PG1, PG2, PG3, PG4
PG5, PG6, PG7, PG8, PG9, PG10, PG11
PG12, PG13, PG14, PG15, SDA, SCL
EMU, EXT_WAKE, PG
PF0, PF1, PH0, PH1, PH2
EXTCLK
PF2, PF3, PF4, PF5, PF6, PF7, PF8, PF9
OL
and V
table.
OL
Total Current Pin Groups
specifications have separate
Total Current Pin
Processor—
OH
/I
OL
) cur-