MT48LC2M32B2TG-6:G Micron Technology Inc, MT48LC2M32B2TG-6:G Datasheet - Page 2

• Manufacturer Part Number: MT48LC2M32B2TG-6:G
• Description: DRAM Chip SDRAM 64M-Bit 2Mx32 3.3V 86-Pin TSOP-II Tray
• Manufacturer: Micron Technology Inc
• Type: SDRAMr

Specifications of MT48LC2M32B2TG-6:G

• Density: 64 Mb
• Maximum Clock Rate: 166 MHz
• Package: 86TSOP-II
• Address Bus Width: 13 Bit
• Operating Supply Voltage: 3.3 V
• Maximum Random Access Time: 17|7.5|5.5 ns
• Operating Temperature: 0 to 70 °C
• Organization: 2Mx32
• Address Bus: 13b
• Access Time (max): 17/7.5/5.5ns
• Operating Supply Voltage (typ): 3.3V
• Package Type: TSOP-II
• Operating Temp Range: 0C to 70C
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Supply Current: 180mA
• Pin Count: 86
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Not Compliant

General Description
Automotive Temperature
PDF: 09005aef811ce1fe/Source: 09005aef811ce1d5
64MSDRAMx32_1.fm - Rev. J 12/08 EN
The Micron
containing 67,108,864 bits. It is internally configured as a quad-bank DRAM with a
synchronous interface (all signals are registered on the positive edge of the clock signal,
CLK). Each of the 16,777,216-bit banks is organized as 2,048 rows by 256 columns by 32
bits.
Read and write accesses to the SDRAM are burst oriented; accesses start at a selected
location and continue for a programmed number of locations in a programmed
sequence. Accesses begin with the registration of an ACTIVE command, which is then
followed by a READ or WRITE command. The address bits registered coincident with the
ACTIVE command are used to select the bank and row to be accessed (BA0, BA1 select
the bank, A0–A10 select the row). The address bits registered coincident with the READ
or WRITE command are used to select the starting column location for the burst access.
The SDRAM provides for programmable read or write burst lengths (BL) of 1, 2, 4, or 8
locations, or the full page, with a burst terminate option. An auto precharge function
may be enabled to provide a self-timed row precharge that is initiated at the end of the
burst sequence.
The 64Mb SDRAM uses an internal pipelined architecture to achieve high-speed opera-
tion. This architecture is compatible with the 2n rule of prefetch architectures, but it also
allows the column address to be changed on every clock cycle to achieve a high-speed,
fully random access. Precharging one bank while accessing one of the other three banks
will hide the PRECHARGE cycles and provide seamless, high-speed, random-access
operation.
The 64Mb SDRAM is designed to operate in 3.3V, low-power memory systems. An auto
refresh mode is provided, along with a power-saving, power-down mode. All inputs and
outputs are LVTTL-compatible.
SDRAMs offer substantial advances in DRAM operating performance, including the
ability to synchronously burst data at a high data rate with automatic column-address
generation, the ability to interleave between internal banks to hide precharge time and
the capability to randomly change column addresses on each clock cycle during a burst
access.
The automotive temperature (AT) option adheres to the following specifications:
• 16ms refresh rate
• Self refresh not supported
• Ambient and case temperatures cannot be less than –40°C or greater than 105°C
®
64Mb SDRAM is a high-speed CMOS, dynamic random-access memory
2
Micron Technology, Inc., reserves the right to change products or specifications without notice.
General Description
©2001 Micron Technology, Inc. All rights reserved.
64Mb: x32 SDRAM