UJA1065 NXP Semiconductors, UJA1065 Datasheet - Page 22

no-image

UJA1065

Manufacturer Part Number
UJA1065
Description
Manufacturer
NXP Semiconductors
Datasheet

Specifications of UJA1065

Lead Free Status / RoHS Status
Supplier Unconfirmed

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
UJA1065/5V0
Manufacturer:
SIPEX
Quantity:
11
Part Number:
UJA1065TW/3V3
Manufacturer:
NXP
Quantity:
4 798
Part Number:
UJA1065TW/3V3
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Part Number:
UJA1065TW/5V0
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
UJA1065TW/5V0/C/T
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
UJA1065TW/5V0/C/T,
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
UJA1065TW/5VO/C/T
Manufacturer:
NXP/恩智浦
Quantity:
20 000
NXP Semiconductors
UJA1065_7
Product data sheet
6.7.4.1 TXDC dominant clamping
6.7.4.2 RXDC recessive clamping
6.7.3 Termination control
6.7.4 Bus, RXD and TXD failure detection
In Active mode, On-line mode and On-line Listen mode, CANH and CANL are terminated
to 0.5 × V
is disabled due to an overload condition both pins become floating.
The UJA1065 can distinguish between bus, RXD and TXD failures as indicated in
All failures are signalled separately in the CANFD bits in the System Diagnosis register.
Any change (detection and recovery) forces an interrupt to the microcontroller, if this
interrupt is enabled.
Table 3.
If the TXDC pin is clamped dominant for longer than t
disabled. After the TXDC pin becomes recessive the transmitter is reactivated
automatically when detecting bus activity or manually by setting and clearing the CTC bit.
If the RXDC pin is clamped recessive while the CAN-bus is dominant the CAN transmitter
is disabled. The transmitter is reactivated automatically when RXDC becomes dominant
or manually by setting and clearing the CTC bit.
Failure
HxHIGH
HxGND
LxHIGH
LxGND
HxL
Bus dom
TXDC dom
RXDC reces
RXDC dom
Fig 9.
CAN wake-up timing diagram.
V2
wake-up
CAN-bus, RXD and TXD failure detection
CANH
CANL
via R
i
. In Off-line mode CANH and CANL are terminated to GND via R
Rev. 07 — 25 February 2010
CANH short-circuit to V
pin RXDC is continuously clamped recessive
pin RXDC is continuously clamped dominant
Description
CANH short-circuit to GND
CANL short-circuit to V
CANL short-circuit to GND
CANH short-circuit to CANL
bus is continuously clamped dominant
pin TXDC is continuously clamped dominant
t
CAN(dom1)
High-speed CAN/LIN fail-safe system basis chip
CC
CC
, V
, V
BAT14
BAT14
t
CAN(reces)
TXDC(dom)
or V
or V
BAT42
BAT42
t
the CAN transmitter is
CAN(dom2)
UJA1065
© NXP B.V. 2010. All rights reserved.
001aad446
Table
i
22 of 76
. If V2
3.

Related parts for UJA1065