IDTSTAC9753XXTAEB2XR IDT, Integrated Device Technology Inc, IDTSTAC9753XXTAEB2XR Datasheet - Page 60
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDTSTAC9753XXTAEB2XR
Manufacturer Part Number
IDTSTAC9753XXTAEB2XR
Description
IC CODEC AC'97 MIC/JACK 48-QFP
Manufacturer
IDT, Integrated Device Technology Inc
Type
Audio Codec '97r
Datasheet
1.IDTSTAC9752XXTAEB2XR.pdf
(95 pages)
Specifications of IDTSTAC9753XXTAEB2XR
Resolution (bits)
20 b
Number Of Adcs / Dacs
2 / 2
Sigma Delta
Yes
Voltage - Supply, Analog
3.14 V ~ 3.47 V; 4.75 V ~ 5.25 V
Voltage - Supply, Digital
3.14 V ~ 3.47 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
48-QFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
STAC9753XXTAEB2XR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDTSTAC9753XXTAEB2XR
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
IDT™
TWO-CHANNEL, 20-BIT, AC’97 2.3 CODECS WITH HEADPHONE DRIVE, SPDIF OUTPUT MICROPHONE & JACK SENSING
STAC9752/9753
TWO-CHANNEL, 20-BIT, AC’97 2.3 CODECS WITH HEADPHONE DRIVE, SPDIF OUTPUT MICROPHONE & JACK SENSING
The Extended Audio ID register is a read only register except for bits D4 and D5. ID1 and ID0 echo
the configuration of the CODEC as defined by the programming of pins 45 and 46 externally. The
primary CODEC returns “00”, while any other code identifies the CODEC as one of three secondary
CODEC possibilities. The AMAP bit, D9, will return a 1 indicating that the CODEC supports the
optional “AC’97 2.3 compliant AC-Link slot to audio DAC mappings”.The default condition assumes
that 0 is loaded into the DSA0 and DSA1 bits of the Extended Audio ID (Index 28h). With 0 in the
DSA1 and DSA0 bits, the CODEC slot assignments are as per the AC’97 specification recommen-
dations. If the DSA1 and DSA0 bits do not contain 0, the slot assignments are as per the table in the
section describing the Extended Audio ID (Index 28h). The VRA bit, D0, will return a 1 indicating that
the CODEC supports the optional variable sample rate conversion as defined by the AC’97 specifi-
cation.
1.
2.
15:14
13:12
11:10
9:6
5:4
Bit
3
2
1
0
External CID pin status (from analog) these bits are the logical inversion of the pin polarity (pin 45-46).
These bits are zero if XTAL_OUT is grounded with an alternate external clock source in primary mode
only. Secondary mode can either be through BIT CLK driven or 24MHz clock driver, with XTAL_OUT
floating.
If pin 48 is held high at powerup, this bit will be held to zero, to indicate the SPDIF is not available.
Pin 48: To Enable SPDIF, use an external 1K - 1 0 K pulldown resistor. To Disable SPDIF, use an
external 1K - 1 0 K pullup resistor. Do NOT leave Pin 48 floating.
RESERVED
DSA [1,0]
REV[1:0]
ID [1,0]
SPDIF
Name
RSVD
RSVD
RSVD
VRA
Read/Write
Read only
Read only
Read only
Read only
Read only
Read only
Read only
Read only
Access
Table 18. Extended Audio ID Register Functions
Reset Value
60
variable
00
10
00
0
0
1
0
1
0,0 = XTAL_OUT grounded (Note 1)
CID1#, CID0# = XTAL_OUT crystal or floating
Bits not used, should read back 00
Indicates CODEC is AC’97 Rev 2.3 compliant
Reserved
DAC slot assignment
If CID[1:0] = 00 then DSA[1:0] resets to 00
If CID[1:0] = 01 then DSA[1:0] resets to 01
If CID[1:0] = 10 then DSA[1:0] resets to 01
If CID[1:0] = 11 then DSA[1:0] resets to 10
00 = left slot 3, right slot 4
01 = left slot 7, right slot 8
10 = left slot 6, right slot 9
11 = left slot 10, right slot 11
RESERVED
0 = SPDIF pulled high on reset, SPDIF disabled
1 = default, SPDIF enabled (Note 2)
RESERVED
Variable sample rates supported (Always = 1)
STAC9752/9753
Function
REV 3.3 1206