PIC16F1947-I/PT Microchip Technology Inc., PIC16F1947-I/PT Datasheet - Page 133

• Manufacturer Part Number: PIC16F1947-I/PT
• Description: 64 TQFP 10x10x1mm TRAY28KB Flash, 1KB RAM, 256B EEPROM, LCD, 1.8-5.5V
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F1947-I/PT

• A/d Inputs: 17-Channel, 10-Bit
• Comparators: 3
• Cpu Speed: 8 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 54
• Interface: CAN/I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 64-pin TQFP
• Programmable Memory: 28K Bytes
• Ram Size: 1K Bytes
• Speed: 32 MHz
• Timers: 4-8-bit, 1-16-bit
• Voltage, Range: 1.8-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

12.4
PORTC is a 8-bit wide, bidirectional port. The
corresponding
(Register
corresponding PORTC pin an input (i.e., put the
corresponding output driver in a High-Impedance mode).
Clearing a TRISC bit (= 0) will make the corresponding
PORTC pin an output (i.e., enable the output driver and
put the contents of the output latch on the selected pin).
Example 12-3
Reading the PORTC register
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
port pins are read, this value is modified and then written
to the PORT data latch (LATC).
The TRISC register
PORTC pin output drivers, even when they are being
used as analog inputs. The user should ensure the bits in
the TRISC register are maintained set when using them
as analog inputs. I/O pins configured as analog input
always read ‘0’.
EXAMPLE 12-3:
 2010 Microchip Technology Inc.
BANKSEL
CLRF
BANKSEL
CLRF
BANKSEL
MOVLW
MOVWF
PORTC Registers
12-11). Setting a TRISC bit (= 1) will make the
PORTC
PORTC
LATC
LATC
TRISC
B'11110000' ;Set RC<7:4> as inputs
TRISC
shows how to initialize PORTC.
data
INITIALIZING PORTC
direction
(Register
;
;Init PORTC
;Data Latch
;
;
;and set RC<3:0> as
;outputs
(Register
12-11) controls the
register
12-10) reads the
is
TRISC
Preliminary
12.4.1
Each PORTC pin is multiplexed with other functions. The
pins, their combined functions and their output priorities
are briefly described here. For additional information,
refer to the appropriate section in this data sheet.
When multiple outputs are enabled, the actual pin
control goes to the peripheral with the lowest number in
the following lists.
Analog input and some digital input functions are not
included in the list below. These input functions can
remain active when the pin is configured as an output.
Certain digital input functions override other port
functions and are included in the priority list.
RC0
1.
2.
3.
RC1
1.
2.
3.
RC2
1.
2.
RC3
1.
2.
3.
RC4
1.
2.
3.
RC5
1.
2.
RC6
1.
2.
3.
RC7
1.
2.
3.
T1OSO (Timer1 Oscillator)
T1CKI (TMR1)
SEG40 (ICD)
T1OSI (Timer1 Oscillator)
CCP2/P2A
SEG32 (ICD)
SEG13 (LCD)
CCP1/P1A
SEG17 (LCD)
SCL1 (MSSP1)
SCK1 (MSSP1)
SEG16 (LCD)
SDA1 (MSSP1)
SDI1 (MSSP1)
SEG12 (LCD)
SDO1 (MSSP1)
SEG27 (LCD)
TX1 (EUSART1)
CK2 (EUSART1)
SEG28 (LCD)
DT1 (EUSART1)
RX1 (EUSART1)
PIC16F/LF1946/47
PORTC FUNCTIONS AND OUTPUT
PRIORITIES
DS41414B-page 133