PIC16F1947-I/PT Microchip Technology Inc., PIC16F1947-I/PT Datasheet - Page 64

• Manufacturer Part Number: PIC16F1947-I/PT
• Description: 64 TQFP 10x10x1mm TRAY28KB Flash, 1KB RAM, 256B EEPROM, LCD, 1.8-5.5V
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F1947-I/PT

• A/d Inputs: 17-Channel, 10-Bit
• Comparators: 3
• Cpu Speed: 8 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 54
• Interface: CAN/I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 64-pin TQFP
• Programmable Memory: 28K Bytes
• Ram Size: 1K Bytes
• Speed: 32 MHz
• Timers: 4-8-bit, 1-16-bit
• Voltage, Range: 1.8-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC16F/LF1946/47
FIGURE 5-3:
DS41414B-page 64
Note 1: A series resistor (R
Note 1: Quartz
C1
C2
2: The value of R
2: Always verify oscillator performance over
3: For oscillator design assistance, reference
quartz crystals with low drive level.
selected (typically between 2 M to 10 M.
• AN826, “Crystal Oscillator Basics and
• AN849, “Basic PIC
• AN943, “Practical PIC
• AN949, “Making Your Oscillator Work”
according
manufacturer. The user should consult the
manufacturer data sheets for specifications
and recommended application.
the V
expected for the application.
the following Microchip Applications Notes:
Crystal Selection for rfPIC
Devices” (DS00826)
(DS00849)
Analysis and Design” (DS00943)
(DS00949)
Quartz
Crystal
R
S
DD
(1)
and temperature range that is
crystal
QUARTZ CRYSTAL
OPERATION (LP, XT OR
HS MODE)
F
to
varies with the Oscillator mode
OSC1/CLKIN
OSC2/CLKOUT
R
S
type,
F
PIC
) may be required for
(2)
®
characteristics
Oscillator Design”
®
®
MCU
Oscillator
®
package
and PIC
Sleep
To Internal
Logic
®
vary
and
Preliminary
FIGURE 5-4:
5.2.1.3
If the oscillator module is configured for LP, XT or HS
modes, the Oscillator Start-up Timer (OST) counts
1024 oscillations from OSC1. This occurs following a
Power-on Reset (POR) and when the Power-up Timer
(PWRT) has expired (if configured), or a wake-up from
Sleep. During this time, the program counter does not
increment and program execution is suspended. The
OST ensures that the oscillator circuit, using a quartz
crystal resonator or ceramic resonator, has started and
is providing a stable system clock to the oscillator
module.
In order to minimize latency between external oscillator
start-up and code execution, the Two-Speed Clock
Start-up mode can be selected (see
“Two-Speed Clock Start-up
5.2.1.4
The oscillator module contains a 4X PLL that can be
used with both external and internal clock sources to
provide a system clock source. The input frequency for
the 4X PLL must fall within specifications. See the PLL
Clock
“Electrical
The 4X PLL may be enabled for use by one of two
methods:
1.
2.
Note 1: A series resistor (R
Program the PLLEN bit in Configuration Word 2
to a ‘1’.
Write the SPLLEN bit in the OSCCON register to
a ‘1’. If the PLLEN bit in Configuration Word 2 is
programmed to a ‘1’, then the value of SPLLEN
is ignored.
C1
C2 Ceramic
2: The value of R
3: An additional parallel feedback resistor (R
Timing
Resonator
ceramic resonators with low drive level.
selected (typically between 2 M to 10 M.
may be required for proper ceramic resonator
operation.
Specifications”.
Oscillator Start-up Timer (OST)
4X PLL
R
Specifications
P
R
(3)
S (1)
CERAMIC RESONATOR
OPERATION
(XT OR HS MODE)
 2010 Microchip Technology Inc.
F
varies with the Oscillator mode
OSC1/CLKIN
OSC2/CLKOUT
Mode”).
S
R
) may be required for
F
PIC
(2)
®
in
MCU
Section 30.0
Section 5.4
To Internal
Logic
Sleep
P
)