PIC16F1947-I/PT Microchip Technology Inc., PIC16F1947-I/PT Datasheet - Page 180

• Manufacturer Part Number: PIC16F1947-I/PT
• Description: 64 TQFP 10x10x1mm TRAY28KB Flash, 1KB RAM, 256B EEPROM, LCD, 1.8-5.5V
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F1947-I/PT

• A/d Inputs: 17-Channel, 10-Bit
• Comparators: 3
• Cpu Speed: 8 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 54
• Interface: CAN/I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 64-pin TQFP
• Programmable Memory: 28K Bytes
• Ram Size: 1K Bytes
• Speed: 32 MHz
• Timers: 4-8-bit, 1-16-bit
• Voltage, Range: 1.8-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC16F/LF1946/47
18.3
A selectable amount of separation voltage can be
added to the input pins of each comparator to provide a
hysteresis function to the overall operation. Hysteresis
is enabled by setting the CxHYS bit of the CM2CON1
register.
See
more information.
18.4
The output resulting from a comparator operation can
be used as a source for gate control of Timer1. See
Section 21.6 “Timer1 Gate”
This feature is useful for timing the duration or interval
of an analog event.
It is recommended that the comparator output be syn-
chronized to Timer1. This ensures that Timer1 does not
increment while a change in the comparator is occur-
ring.
18.4.1
The output from a comparator can be synchronized
with Timer1 by setting the CxSYNC bit of the
CMxCON0 register.
Once enabled, the comparator output is latched on the
falling edge of the Timer1 source clock. If a prescaler is
used with Timer1, the comparator output is latched after
the prescaling function. To prevent a race condition, the
comparator output is latched on the falling edge of the
Timer1 clock source and Timer1 increments on the
rising edge of its clock source. See the Comparator
Block Diagram
Diagram
DS41414B-page 180
Section 30.0 “Electrical Specifications”
Comparator Hysteresis
Timer1 Gate Operation
(Figure
COMPARATOR OUTPUT
SYNCHRONIZATION
(Figure
21-1) for more information.
18-2) and the Timer1 Block
for more information.
Preliminary
for
18.5
An interrupt can be generated upon a change in the
output value of the comparator for each comparator, a
rising edge detector and a Falling edge detector are
present.
When either edge detector is triggered and its associ-
ated enable bit is set (CxINTP and/or CxINTN bits of
the CMxCON1 register), the Corresponding Interrupt
Flag bit (CxIF bit of the PIR2 register) will be set.
To enable the interrupt, you must set the following bits:
• CxON, CxPOL and CxSP bits of the CMxCON0
• CxIE bit of the PIE2 register
• CxINTP bit of the CMxCON1 register (for a rising
• CxINTN bit of the CMxCON1 register (for a falling
• PEIE and GIE bits of the INTCON register
The associated interrupt flag bit, CxIF bit of the PIR2
register, must be cleared in software. If another edge is
detected while this flag is being cleared, the flag will still
be set at the end of the sequence.
18.6
Configuring the CxPCH<1:0> bits of the CMxCON1
register directs an internal voltage reference or an
analog pin to the non-inverting input of the comparator:
• CxIN+ analog pin
• DAC
• FVR (Fixed Voltage Reference)
• V
See
for more information on the Fixed Voltage Reference
module.
See
(DAC) Module”
signal.
Any time the comparator is disabled (CxON = 0), all
comparator inputs are disabled.
register
edge detection)
edge detection)
Note:
SS
Section 14.0 “Fixed Voltage Reference (FVR)”
Section 17.0 “Digital-to-Analog
(Ground)
Comparator Interrupt
Comparator Positive Input
Selection
Although a comparator is disabled, an
interrupt can be generated by changing
the output polarity with the CxPOL bit of
the CMxCON0 register, or by switching
the comparator on or off with the CxON bit
of the CMxCON0 register.
for more information on the DAC input
 2010 Microchip Technology Inc.
Converter