HD64570F16 Renesas Electronics America, HD64570F16 Datasheet - Page 211
HD64570F16
Manufacturer Part Number
HD64570F16
Description
IC SCA SRL COMM ADAPTER 88QFP
Manufacturer
Renesas Electronics America
Datasheet
1.HD64570F16.pdf
(469 pages)
Specifications of HD64570F16
Applications
ISDN
Interface
Serial
Voltage - Supply
4.75 V ~ 5.25 V
Package / Case
88-QFP
Mounting Type
Surface Mount
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (min)
4.5V
Operating Supply Voltage (max)
5.5V
Operating Temp Range
-20C to 75C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HD64570F16
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
HD64570F16
Manufacturer:
HITACHI/日立
Quantity:
20 000
Company:
Part Number:
HD64570F16V
Manufacturer:
INFINEON
Quantity:
12 000
- Current page: 211 of 469
- Download datasheet (3Mb)
Error Checking: Involves the following items.
CRC error and CRC code transmission
The MSCI supports two CRC code types: CRC-16 and CRC-CCITT. The program can select
the type to be used and the initial value (all 0s or 1s) with the CRC1 CRC0 bits of MD0.
16
15
2
16
12
5
The CRC polynomial is X
+ X
+ X
+ 1 for CRC-16, and X
+ X
+ X
+ 1 for CRC-
CCITT.
The transmitter and receiver both have a CRC calculator.
The TX CRC calculator is automatically initialized immediately before data field transmission.
It can also be initialized when a TX CRC initialization command is issued.
During transmission, SYN characters are excluded from the CRC calculation. Specific data
can also be excluded (in character units) from the CRC calculation by a TX CRC calculation
exclusion command. Use the CRCCC bit of MD0 and the end of message command to enable
CRC code transmission. The CRC code is transmitted automatically when both the CRCCC
bit and the UDRNC bit of CTL are set to 1 in underrun state. If an underrun error occurs while
UDRNC or CRCCC is 0, the MSCI directly enters idle state without transmitting the CRC
code. For details, see section 5.2.1, MSCI Mode Register 0 (MD0), section 5.2.4, MSCI
Control Register (CTL), and section 5.2.8, MSCI Command Register (CMD).
The RX CRC calculator is automatically initialized immediately before data field reception. It
can also be initialized when an RX CRC initialization command is issued.
During reception, the characters not to be input to the receive buffer, such as SYN characters,
are excluded from the CRC calculation. Specific data can be also excluded (by character) from
the CRC calculation by an RX CRC calculation exclusion command. The CRC code check is
completed 15 system clock cycles after the character following the last checked character has
entered the receive buffer. If a CRC calculation forcing command is issued and if the character
following the last character does not enter the receive buffer, the check is completed 15 system
clock cycles after the command has been issued. In either case, the CRC error status is valid
until the next character enters the receive buffer.
When a CRC error is detected, the CRCE bit of status register 2 (ST2) is set to 1. This
generates an interrupt request (if enabled). For details, see section 5.2.11, MSCI Status
Register 2 (ST2).
Overrun error
An overrun error occurs when the receive buffer is full when new data is transferred.
When an overrun error occurs, the new data overwrites the top stage of the receive buffer,
erasing the previous data. At the same time, the top stage of the status FIFO is overwritten
with the status (indicating an overrun) of the new data.
The OVRN bit of ST2 is set to 1 when the new data is ready to be read. This generates an
interrupt request (if enabled).
Even if an overrun error occurs, subsequent characters are received normally. However, the
OVRN bit is not cleared even if the subsequent data causes no overrun error. It is cleared only
when a 1 is written to the bit position or ST2 is reset.
Rev. 0, 07/98, page 195 of 453
Related parts for HD64570F16
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
(HD64 Series) Hitachi Single-Chip Microcomputer
Manufacturer:
Hitachi Semiconductor
Datasheet:
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet: