ATxmega32D4 Atmel Corporation, ATxmega32D4 Datasheet - Page 158
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATxmega32D4
Manufacturer Part Number
ATxmega32D4
Description
Manufacturer
Atmel Corporation
Specifications of ATxmega32D4
Flash (kbytes)
32 Kbytes
Pin Count
44
Max. Operating Frequency
32 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
34
Ext Interrupts
34
Usb Speed
No
Usb Interface
No
Spi
4
Twi (i2c)
2
Uart
2
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
12
Adc Resolution (bits)
12
Adc Speed (ksps)
200
Analog Comparators
2
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.6 to 3.6
Operating Voltage (vcc)
1.6 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
14
Input Capture Channels
14
Pwm Channels
14
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATxmega32D4-AU
Manufacturer:
Atmel
Quantity:
123
Part Number:
ATxmega32D4-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATxmega32D4-CU
Manufacturer:
Maxim
Quantity:
71
Company:
Part Number:
ATxmega32D4-MH
Manufacturer:
Atmel
Quantity:
1 910
Company:
Part Number:
ATxmega32D4-MH
Manufacturer:
Atmel
Quantity:
1 704
Part Number:
ATxmega32D4-MH
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
14.7.4
14.7.5
8210B–AVR–04/10
STATUS - Status Register
DTBOTH - Dead-time Concurrent Write to Both Sides
Table 14-1.
• Bit 7:3 - Reserved
These bits are reserved and will always be read as zero. For compatibility with future devices,
always write these bits to zero when this register is written.
• Bit 2 - FDF: Fault Detect Flag
This flag is set when a fault detect condition is detected, i.e. when an event is detected on one of
the event channels enabled by the FDEVMASK. This flag is cleared by writing a one to its bit
location.
• Bit 1 - DTHSBUFV: Dead-Time High Side Buffer Valid
If this bit is set the corresponding DT buffer is written and contains valid data that will be copied
into the DTLS Register on the UPDATE condition. If this bit is zero no action will be taken. The
connected Timer/Counter’s lock update (LUPD) flag also affects the update for dead time
buffers.
• Bit 0 - DTLSBUFV: Dead-Time Low Side Buffer Valid
If this bit is set the corresponding DT buffer is written and contains valid data that will be copied
into the DTHS Register on the UPDATE condition. If this bit is zero no action will be taken. Note
that the connected Timer/Counter unit's lock update (LUPD) flag also affects the update for dead
time buffers.
Bit
+0x04
Read/Write
Initial Value
Bit
+0x06
Read/Write
Initial Value
FDACT[1:0]
00
01
11
R/W
Fault actions
R
7
–
0
7
0
Group Configuration
R
6
–
0
R/W
6
0
CLEARDIR
CLEAROE
NONE
R
5
–
0
R/W
5
0
R
4
–
0
R/W
4
0
Description
None (Fault protection disabled)
Clear all override enable (OUTOVEN) bits, i.e. disable
the output override.
Clear all Direction (DIR) bits, which correspond to
enabled DTI channel(s), i.e. tri-state the outputs
DTBOTH[7:0]
R
3
–
0
R/W
3
0
FDF
R/W
2
0
R/W
2
0
DTHSBUFV
R/W
1
0
R/W
1
0
DTLSBUFV
XMEGA D
R/W
0
0
R/W
0
0
STATUS
DTBOTH
158