AD9125 Analog Devices, AD9125 Datasheet - Page 39
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD9125
Manufacturer Part Number
AD9125
Description
Manufacturer
Analog Devices
Datasheet
1.AD9125.pdf
(56 pages)
Specifications of AD9125
Resolution (bits)
16bit
Dac Update Rate
1GSPS
Dac Settling Time
n/a
Max Pos Supply (v)
+3.47V
Single-supply
No
Dac Type
Current Out
Dac Input Format
Par
QUADRATURE PHASE CORRECTION
The purpose of the quadrature phase correction block is to
enable compensation of the phase imbalance of the analog
quadrature modulator following the DAC. If the quadrature
modulator has a phase imbalance, the unwanted sideband appears
with significant energy. Tuning the quadrature phase adjust value
can optimize image rejection in single sideband radios.
Ordinarily, the I and Q channels have an angle of precisely 90°
between them. The quadrature phase adjustment is used to
change the angle between the I and Q channels. When the
I phase adjust[9:0] is set to 1000000000, the I DAC output
moves approximately 1.75° away from the Q DAC output,
creating an angle of 91.75° between the channels. When the I
phase adjust[9:0] is set to 0111111111, the I DAC output moves
approximately 1.75° toward the Q DAC output, creating an
angle of 88.25° between the channels.
The Q phase adjust bits (Bits[9:0]) work in a similar fashion.
When the Q phase adjust[9:0]) is set to 1000000000, the Q DAC
output moves approximately 1.75° away from the I DAC output,
creating an angle of 91.75° between the channels. When the
Q phase adjust[9:0] is set to 0111111111, the Q DAC output
moves approximately 1.75° toward the I DAC output, creating
an angle of 88.25° between the channels.
Based on these two endpoints, the combined resolution of the
phase compensation register is approximately 3.5°/1024, or
0.00342°, per code.
DC OFFSET CORRECTION
The dc value of the I datapath and the Q datapath can be inde-
pendently controlled by adjusting the I DAC offset[15:0] and
Q DAC offset[15:0] values in Register 0x3C through Register 0x3F.
These values are added directly to the datapath values. Care should
be taken not to overrange the transmitted values.
Figure 61 shows how the DAC offset current varies as a function of
the I DAC offset[15:0] and Q DAC offset[15:0] values. With the
digital inputs fixed at midscale (0x0000, twos complement data
format), Figure 61 shows the nominal I
as the DAC offset value is swept from 0 to 65,535. Because I
and I
and I
OUTxN
OUTxN
are complementary current outputs, the sum of I
is always 20 mA.
OUTxP
and I
OUTxN
currents
OUTxP
OUTxP
Rev. 0 | Page 39 of 56
INVERSE SINC FILTER
The inverse sinc (sinc
composite response of the sinc
the DAC is shown in Figure 62. The composite response has less
than ±0.05 dB pass-band ripple up to a frequency of 0.4 × f
To provide the necessary peaking at the upper end of the pass
band, the inverse sinc filters have an intrinsic insertion loss of
about 3.2 dB. Figure 62 shows the composite frequency response.
The sinc
the bypass sinc
Figure 62. Sample Composite Responses of the Sinc
0x0000
20
15
10
5
0
–3.0
–3.2
–3.4
–3.6
–3.8
–4.0
−1
0
filter is enabled by default. It can be bypassed by setting
Figure 61. DAC Output Currents vs. DAC Offset Value
−1
0x4000
bit (Register 0x1B, Bit 6).
0.1
−1
DAC OFFSET VALUE
) filter is a nine-tap FIR filter. The
0x8000
0.2
f
−1
OUT
and the sin(x)/x response of
/
f
DAC
0.3
0xC000
−1
Filter with Sin(x)/x Roll-Off
0.4
0xFFFF
AD9125
0
5
10
15
20
DACCLK
0
.5
.