ST7LITE49M STMicroelectronics, ST7LITE49M Datasheet - Page 72
ST7LITE49M
Manufacturer Part Number
ST7LITE49M
Description
8-bit MCU
Manufacturer
STMicroelectronics
Datasheet
1.ST7LITE49M.pdf
(187 pages)
Specifications of ST7LITE49M
4 Kbytes Single Voltage Extended Flash (xflash) Program Memory With Read-out Protection In-circuit Programming And In-application Programming (icp And Iap) Endurance
10k write/erase cycles guaranteed Data retention
128 Bytes Data Eeprom With Read-out Protection. 300k Write/erase Cycles Guaranteed, Data Retention
20 years at 55 °C.
Clock Sources
Internal trimmable 8 MHz RC oscillator, auto-wakeup internal low power - low frequency oscillator, crystal/ceramic resonator or external clock
Five Power Saving Modes
Halt, Active-halt, Auto-wakeup from Halt, Wait and Slow
A/d Converter
10 input channels
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 72 of 187
- Download datasheet (2Mb)
I/O ports
10.2.4
Caution:
10.3
10.4
10.5
72/188
Analog alternate function
Configure the I/O as floating input to use an ADC input. The analog multiplexer (controlled
by the ADC registers) switches the analog voltage present on the selected pin to the
common analog rail, connected to the ADC input.
Analog Recommendations
Do not change the voltage level or loading on any I/O while conversion is in progress. Do not
have clocking pins located close to a selected analog pin.
The analog input voltage level must be within the limits stated in the absolute maximum
ratings.
I/O port implementation
The hardware implementation on each I/O port depends on the settings in the DDR and OR
registers and specific I/O port features such as ADC input or open-drain.
Switching these I/O ports from one state to another should be done in a sequence that
prevents unwanted side effects. Recommended safe transitions are illustrated in
Other transitions are potentially risky and should be avoided, since they may present
unwanted side-effects such as spurious interrupt generation.
Figure 35. Interrupt I/O port state transitions
Unused I/O pins
Unused I/O pins must be connected to fixed voltage levels. Refer to
pin
Low power modes
Table 26.
s
characteristics.
Mode
Wait
Halt
Effect of low power modes on I/O ports
No effect on I/O ports. External interrupts cause the device to exit from Wait
No effect on I/O ports. External interrupts cause the device to exit from Halt
floating/pull-up
interrupt
INPUT
01
Doc ID 13562 Rev 3
(reset state)
floating
INPUT
00
open-drain
OUTPUT
XX
Description
10
mode.
mode.
= DDR, OR
OUTPUT
push-pull
11
Section 13.9: I/O port
ST7LITE49M
Figure
35.
Related parts for ST7LITE49M
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: