SC28L202 Philips Semiconductors, SC28L202 Datasheet - Page 49

• Manufacturer Part Number: SC28L202
• Description: Dual universal asynchronous receiver/transmitter DUART
• Manufacturer: Philips Semiconductors

Philips Semiconductors
MR1 Mode Register 1
NOTE: * In block error mode the block error conditions must be cleared by using the error reset command (command 0x40) or a receiver reset.
MR1 A is accessed when the Channel A MR pointer points to MR1.
The pointer is set to MR1 by RESET or by a ‘set pointer’ command
applied via CR command 1. After reading or writing MR1 A, the
pointer will point to MR2 A.
MR1 A[7] – Channel A Receiver Request–to–Send Control (Flow
Control)
This bit controls the deactivation of the RTSN A output (I/O0 B) by
the receiver. This output is normally asserted by setting OPR[0]B
and negated by resetting OPR[0]B.
MR1 A[7] = 1 causes RTSN A to be negated (I/O0 B is driven to a ‘1’
[V
This is the beginning of the reception of the ninth byte. If the FIFO is
not read before the start of the tenth byte, an overrun condition will
occur and the tenth byte will be lost. However, the bit in OPR[0] is
not reset and RTSN A will be asserted again when an empty FIFO
position is available. This feature can be used for flow control to
prevent overrun in the receiver by using the RTSN A output signal to
control the CTSN input of the transmitting device.
MR1[6] – Receiver interrupt control bit 1. See description under
MR0[6].
MR1 A[5] – Channel A Error Mode Select
This bit select the operating mode of the three FIFOed status bits
(FE, PE, received break) for Channel A. In the ‘character’ mode,
status is provided on a character–by–character basis; the status
applies only to the character at the top of the FIFO. In the ‘block’
MR2 Mode Register 2
NOTE: *Add 0.5 to values shown for 0 – 7 if channel is programmed
for 5 bits/char.
2000 Feb 10
MR1 A
MR1 B
MR2 A
MR2 B
CC
Dual UART
]) upon receipt of a valid start bit if the Channel A FIFO is full.
Bit 7
CHANNEL MODE
00 = Normal
01 = Auto–Echo
10 = Local loop
11 = Remote loop
Bit 7
Rx
CONTROLS
RTS
0 = No
1 = Yes
BIT 6
BIT 6
RxINT
BIT 1
0 = RxRDY
1 = FFULL
BIT 5
Tx CONTROLS RTS
0 = No
1 = Yes
BIT 5
ERROR
MODE
0 = Char
1 = Block
BIT 4
CTS
ENABLE Tx
0 = No
1 = Yes
Bit (4:3)
PARITY MODE
00 = With Parity
01 = Force Parity
10 = No Parity
11 = Multi–drop Mode
43
BIT 3
STOP BIT LENGTH
NOTE: Add 0.5 to binary codes 0 – 7 for 5 bit character lengths.
0 = 0.563 4 = 0.813 8 = 1.563 C = 1.813
1 = 0.625 5 = 0.875 9 = 1.625 D = 1.875
2 = 0.688 6 = 0.938 A = 1.688 E = 1.938
3 = 0.750 7 = 1.000 B = 1.750 F = 2.000
mode, the status provided in the SR for these bits is the
accumulation (logical–OR) of the status for all characters coming to
the top of the FIFO since the last ‘reset error’ command for Channel
A was issued.
MR1 A[4:3| – Channel A Parity Mode Select
If ‘with parity’ or ‘force parity’ is selected a parity bit is added to the
transmitted character and the receiver performs a parity check on
incoming data
MR1 A[4:3] = 11 selects Channel A to operate in the special
multi–drop mode described in the Operation section.
MR1 A[2] – Channel A Parity Type Select
Selects the parity type (odd or even) if the “‘with parity” mode is
programmed by MR1 A[4:3], and the polarity of the forced parity bit if
the ‘force parity’ mode is programmed; no effect if ‘no parity’ is
programmed. In the special multi–drop mode it selects the polarity of
the A/D bit.
MR1 A[1:0] – Channel A Bits Per Character Select
This field selects the number of data bits per character to be
transmitted and received. The character length does not include the
start, parity, and stop bits.
MR2 A is accessed when the Channel A MR pointer points to MR2,
which occurs after any access to MR1 A. Accesses to MR2 A do not
change the pointer.
See description in the previous MR2 description
BIT 2
BIT 2
PARITY
TYPE
0 = Even
1 = Odd
BIT 1
Bits (1:0)
BITS PER
CHARACTER
00 = 5
01 = 6
10 = 7
11 = 8
BIT 0
Objective specification
SC28L202